ATTO Technology 5300 RAIDCommandTimeout, RAIDRebuildPriority, Reserve, ResetFCPortErrors

Page 44

RAIDCommandTimeout

Specifies in milliseconds the range of time the drives have to respond. You must use RGCommit before using this command.

CAUTION

If you set this value too low, failures may occur during normal operation.

Default: 30000

set RAIDCommandTimeout [100 - 3600000] get RAIDCommandTimeout

RAIDRebuildPriority

Sets or displays the RAID rebuild priority. A RAID rebuild priority set to high gives higher priority to RAID rebuilds and lower priority to the processing of simultaneous I/O transactions. A RAID rebuild priority set to low gives lower priority to the rebuild and a higher priority to I/O transactions. Set same, the RAID rebuild and processing of I/O transactions is the same.

Default: same

set RAIDRebuildPriority [high low same] get RAIDRebuildPriority

Reserve

Reports the state of CLI reservation for the current CLI session. If the command reports that Reservations are enabled, then another CLI session has control of parameter modification on the unit.

Reserve

ResetFCPortErrors

ResetFCPortErrors resets all Fibre Channel error counts for the specified port to zero. See FCPortErrors.

ResetFCPortErrors [fp]

RestoreConfiguration

Issued with the default option, forces the unit NVRAM settings to their original defaults. The saved option undoes any changes made to this session since the last save.

RestoreConfiguration < Default Saved >

xv

RGAddStorage

Adds additional storage to an existing RAID Group. MirrorStripeSpan specifies the method used to expand the storage. Optional parameter BlockDeviceID specifies available block device(s) to be added to the RAID Group. Optional parameter commit specifies that the RGCommit command is run automatically.

Note

Mirrors cannot be added to a RAID 5 group.

RGAddStorage [GroupName] [Mirror Stripe Span] <BlockDeviceID> <commit>

RGCancelAddStorage

Cancels the RGAddStorage command.

RGCancelAddStorage [GroupName]

RGCommit

Stamps a NEW RAID Group’s configuration to its member drives. After this command, a RAID Group can be considered operational and transitions from the NEW state to the Online, Degraded, or Offline state depending on the health of the selected member drives. RGCommit also stamps an EXISTING RAID Group’s configuration to its member drives, when the EXISTING RAID Group is in the process of having storage added.

RGCommit [GroupName all]

RGCreate

Creates a NEW empty RAID Group. GroupName is an ASCII name for the RAID Group (15 chars max, no spaces). The optional value after the RAID Group type parameter represents the desired interleave for the RAID Group. If this value is not provided then the system- default interleave size is used.

RGCreate [GroupName] [RAID [01105] JBOD] <163264128256>

RGDelete

Deletes the specified RAID Group. If All is used, the command deletes all existing RAID groups that do not have mapped Virtual drives. Any commands outstanding to the RAID Group when this command is issued are completed before deleting the RAID Group. A successful delete clears the configuration area of the member drives. This command fails if the specified RAID Group does not exist. You are asked to confirm the delete if you have enabled verbose mode.

RGDelete [GroupName All]

ATTO Technology Inc. FastStream VT 5300 Installation and Operation Manual

Page 43 Page 45
Image 44
Page 43 Page 45
Contents FastStream VT Page Page Contents Update storage and firmware Appendix E Warranty, contact information XxiModify storage Interface optionsHardware features Virtual Tape featuresBackup and restore features Management and control featuresGbE network Gb FC Switch GbE SwitchEthernet Fibre Channel Physical attributes Installation Installation Unpack the packing box verify contentsInstall the FastStream Install Windows driversBegin initial configuration Click on Launch BrowserConfigure Virtual Tape Use quick initial configuration Use custom initial setupUse Hot Spare devices Click on the Add/Remove Hot Spares buttonClick in the Enable/Disable Write Protection button Enable/Disable Write Protection page appearsSecure data through Write Protection Move Virtual Tape CartridgesOptional changes to system parameters Customize the username, passwordChange system configurations Changes to other parameters may be made using the Advanced Advanced CLIMonitor storage and diagnose configurations Monitor VTLPhone home E-mail messages Configuration DisplayHealth and Status Monitor Measure drive performance Click the Set up Error Notification buttonConfiguration Scan drive surfaces Verify storageClick the Initialize and Verify button Select Verify OnlyAdd drives to a RAID Group Modify storageInitialize and verify drives Rebuild RAID Groups Add or remove Hot SparesSelect Rebuild RAID Groups Select the Add/Remove Hot Spares buttonClick in the Delete Virtual Tape Library button Add a VTL from another FastStream VTLDelete a VTL Move Virtual Tape Cartridges Update storage and firmware Remove stale VTL configuration dataUpdate firmware Preliminary stepsUse FTP over Ethernet Use the RS-232 serial linkSend File Click Send FileType FastStream VT 5300 in the New Connection dialog box Interface optionsUse the serial port Use Telnet EnterCable types Appendix a CablingScsi cabling Fibre Channel connections Cable lengthAppendix B Designing RAID groups Jbod Just a Bunch of DisksRAID Level DiskIv Appendix Symbol Indicates Appendix C CLI provides an ASCII-based interfaceCLI error messages Mp1Command Default Example CLI summaryViii Appendix Sntp CLI command explanations DefaultInterleave DHCPFixedDelayDriveTestConfig DumpConfigEmailPassword EmailNotifyAddressEmailServerAddress EmailUsernameFCPortErrors FCDataRateFCHard FCHardAddressPassword IPGatewayIPSubnetMask IsReservedRAIDCommandTimeout ResetFCPortErrorsRestoreConfiguration RGCancelAddStorageRGWaitTimeout RGDisplayRGHaltConversion RGHaltRebuildSaveConfiguration SCSIPortResetSCSIPortResetOnStartup RMStatusSerialPortBaudRate SerialPortEchoSNTPServer TailEventLogThis equipment generates, uses, and can radiate radio Further results of FCC TestingAppendix D Standards and compliances European Standards Declaration of ConformityContact Atto Technology, Inc Appendix E Warranty, contact informationManufacturer limited warranty Xxii Appendix
Top Page Image Contents