Tripp Lite 350, 525 owner manual Basic Operation, Buttons Front Panel

Page 8

200310077 93-2200 Sinewave SmartPro Rackmount UPS Owner’s Manual.qxd 10/21/2003

3:32 PM Page 7

Basic Operation

Buttons (Front Panel)

“POWER” Button

•To turn the UPS ON: with the UPS plugged into a live AC wall outlet*, press and hold the POWER button for one second.** Release the button. If utility power is absent, you can “cold-start” the UPS (i.e.: turn it ON and supply power for a limited time from its batteries***) by pressing and holding the POWER button for one second.**

•To turn the UPS OFF: with the UPS ON and receiving utility power, press and hold the POWER button for one second.** Then unplug the UPS from the wall outlet. The UPS will be completely OFF.

*After you plug the UPS into a live AC outlet, the UPS will automatically charge its batteries, but will not supply power to its outlets until it is turned ON. ** The alarm will beep once briefly after the indi- cated interval has passed. *** If fully charged.

“MUTE/TEST” Button

To Silence (or “Mute”) UPS Alarms: briefly press and release the MUTE/TEST button.*

To Run a Self-Test: with your UPS plugged in and turned ON, press and hold the MUTE/TEST button for two seconds.* Continue holding the button until the alarm beeps several times and the UPS performs a self test. See “Results of a Self-Test” below. Note: you can leave connected equipment on during a self-test. Your UPS, however, will not perform a self-test if you have placed it in “Standby/Charge-Only” mode (see “POWER” Button description).

CAUTION! Do not unplug your UPS to test its batteries. This will remove safe electrical grounding and may introduce a damaging surge into your network connections.

Results of a Self-Test: The test will last approximately 10 seconds as the UPS switches to battery to test its load capacity and battery charge. All LEDs will be lit and the UPS alarm will sound.

•If the “OUTPUT LOAD LEVEL” LED remains lit red and the alarm contin- ues to sound after the test, the UPS’s outlets are overloaded. To clear the over- load, unplug some of your equipment and run the self-test repeatedly until the “OUTPUT LOAD LEVEL” LED is no longer lit red and the alarm is no longer sounding.

CAUTION! Any overload that is not corrected by the user immediately following a self-test may cause the UPS to shut down and cease supplying output power in the event of a blackout or brownout.

•If the “BATTERY WARNING” LED remains lit and the alarm continues to sound after the test, the UPS batteries need to be recharged or replaced. Allow the UPS to recharge continuously for 12 hours, and repeat the self-test. If the LED remains lit, contact Tripp Lite for service. If your UPS requires battery replacement, visit www.tripplite.com/ support/battery/index.cfm to locate the specific Tripp Lite replacement battery for your UPS.

* The alarm will beep once briefly after the indicated interval has passed.

7

Page 7 Page 9
Image 8
Page 7 Page 9
Contents SmartPro Rackmount Intelligent, Line-Interactive UPS SystemsPage Important Safety Instructions Battery WarningsUPS Location Warnings UPS Connection WarningsMounting Rack Post MountingMounting Tower Post Telecom MountingTurn the UPS on Plug the UPS into an outlet on a dedicated circuitPlug your equipment into the UPS External Battery Connection select models Buttons Front Panel Indicator Lights Front Panel Other UPS Features Rear Panel Basic Operation Service StorageProcedure Two symbols are used on the label ~ AC Voltage DC Voltage Page Manual del propietario Inteligentes e interactivos con la líneaInstrucciones de seguridad importantes Advertencias sobre la ubicación del UPSAdvertencias sobre la conexión del UPS Advertencias sobre la conexión de equiposMontaje Bastidor Montaje de 4 postesMontaje en bastidor continúa Montaje En torreMontaje de 2 postes Telecomunicaciones Tolos los modelos de UPSEncienda el UPS Conecte el UPS en una salida de un circuito dedicadoConecte sus equipos en el UPS Conexión de batería externa modelos exclusivos Comunicaciones USB y serie RS-232 todos los modelosConexión de puerto EPO todos los modelos Botones Panel frontal Operación básica continúa Luces indicadoras Panel frontalOtras funciones del UPS Panel posterior Operación básica continúa Servicio AlmacenamientoProcedimiento Nota sobre el rotulado Manuel du propriétaire Systèmes UPS intelligent, en attente activeMises en garde Emplacement de lUPS Directives de sécurité importantesMises en garde Connexions de lUPS Mises en garde Connexion déquipementMontage Bâti Bâti à quatre montantsMontage bâti suite Montage TourMontage sur 2 montants Télécom Tous les modèles dUPSMettre lUPS sous tension Brancher lUPS dans une prise dun circuit dédiéConnecter votre équipement à lUPS Connexion au port EPO tous les modèles Connexion de batterie externe modèles sélectBoutons Panneau avant Fonctionnement de base, suite Voyants indicateurs Panneau avantAutres caractéristiques de lUPS panneau arrière Fonctionnement de base, suite Service EntreposageProcédure Modèle
Top Page Image Contents