Tripp Lite 525, 350 owner manual Indicator Lights Front Panel

Page 9

200310077 93-2200 Sinewave SmartPro Rackmount UPS Owner’s Manual.qxd 10/21/2003

3:32 PM Page 8

Basic Operation continued

Indicator Lights (Front Panel)

All Indicator Light descriptions apply when the UPS is plugged into a wall outlet and turned ON.

“POWER” LED: this green LED lights continuously when the UPS is ON and supplying connected equipment with AC power from a utility source. The LED flashes and an alarm sounds (4 short beeps followed by a pause) to indicate the UPS is operating from its internal batteries during a blackout or severe brownout. If the blackout or severe brownout is prolonged, you should save files and shut down your equipment since internal battery power will eventual- ly be depleted. See “BATTERY CHARGE” LED description below.

“VOLTAGE CORRECTION” LED: this green LED lights continuously whenever the UPS is automatically correcting high or low AC voltage on the utility line without the assistance of battery power. The UPS will also emit a slight clicking noise. These are normal, automatic operations of the UPS, no action is required on your part.

“OUTPUT LOAD LEVEL” LED: this multicolored LED indicates the approximate electrical load of equipment connected to the UPS's AC outlets. It will turn from green (light load) to yellow (medium load) to red (overload). If the LED is red (either illuminated continuously or flashing), clear the overload immediately by unplugging some of your equipment from the outlets until the LED changes from red to yellow (or green). CAUTION! Any overload that is not corrected by the user immediately may cause the UPS to shut down and cease supplying output power in the event of a blackout or brownout.

“BATTERY CHARGE” LED: when the UPS is operating from utility power, this LED indicates the approximate charge state of the UPS's internal batteries: red indicates the batteries are beginning to charge; yellow indicates the batteries are roughly midway through charging; and green indicates the batteries are fully charged. When the UPS is operating from battery power during a blackout or severe brownout, this LED indicates the approximate amount of energy (ulti- mately affecting runtime) which the UPS’s batteries will provide: red indicates a low level of energy; yellow indicates a medium level of energy; and green indicates a high level of energy. Since the runtime performance of all UPS bat- teries will gradually deplete over time, it is recommended that you periodically perform a self-test (see MUTE/TEST Button description) to determine the energy level of your UPS batteries BEFORE a blackout or severe brownout occurs. During a prolonged blackout or severe brownout, you should save files and shut down your equipment since battery power will eventually be depleted. When the LED turns red and an alarm sounds continuously, it indicates the UPS's batteries are nearly out of power and UPS shut down is imminent.

“BATTERY WARNING” LED: this LED lights red and an alarm sounds intermittently after you initiate a self test (See “MUTE/TEST” Button description) to indicate the UPS batteries need to be recharged or replaced. Allow the UPS to recharge continuously for 12 hours, and repeat the self-test. If the LED contin- ues to light, contact Tripp Lite for service. If your UPS requires battery replace- ment, visit www.tripplite.com/support/battery/index.cfm to locate the specific Tripp Lite replacement battery for your UPS.

8

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Intelligent, Line-Interactive UPS Systems SmartPro RackmountPage Battery Warnings Important Safety InstructionsUPS Location Warnings UPS Connection WarningsPost Mounting Mounting RackPost Telecom Mounting Mounting Tower Plug the UPS into an outlet on a dedicated circuit Plug your equipment into the UPS Turn the UPS on External Battery Connection select models Buttons Front Panel Indicator Lights Front Panel Other UPS Features Rear Panel Basic Operation Storage ServiceProcedure Two symbols are used on the label ~ AC Voltage DC Voltage Page Inteligentes e interactivos con la línea Manual del propietarioAdvertencias sobre la ubicación del UPS Instrucciones de seguridad importantesAdvertencias sobre la conexión del UPS Advertencias sobre la conexión de equiposMontaje de 4 postes Montaje BastidorMontaje En torre Montaje en bastidor continúaMontaje de 2 postes Telecomunicaciones Tolos los modelos de UPSConecte el UPS en una salida de un circuito dedicado Conecte sus equipos en el UPSEncienda el UPS Comunicaciones USB y serie RS-232 todos los modelos Conexión de puerto EPO todos los modelosConexión de batería externa modelos exclusivos Botones Panel frontal Luces indicadoras Panel frontal Operación básica continúaOtras funciones del UPS Panel posterior Operación básica continúa Almacenamiento ServicioProcedimiento Nota sobre el rotulado Systèmes UPS intelligent, en attente active Manuel du propriétaireDirectives de sécurité importantes Mises en garde Emplacement de lUPSMises en garde Connexions de lUPS Mises en garde Connexion déquipementBâti à quatre montants Montage BâtiMontage Tour Montage bâti suiteMontage sur 2 montants Télécom Tous les modèles dUPSBrancher lUPS dans une prise dun circuit dédié Connecter votre équipement à lUPSMettre lUPS sous tension Connexion de batterie externe modèles sélect Connexion au port EPO tous les modèlesBoutons Panneau avant Voyants indicateurs Panneau avant Fonctionnement de base, suiteAutres caractéristiques de lUPS panneau arrière Fonctionnement de base, suite Entreposage ServiceProcédure Modèle
Top Page Image Contents