Schneider Electric XPSMF2DO801 manual HIMatrix

Page 14

Overview

Mounting the Mount the remote output module horizontally (so the F2DO logo on the front panel

Remote Output is facing the user) to allow sufficient ventilation. We advise not to mount the remote

Moduleoutput module in a vertical position, because in this case additional measures are required to ensure the device does not move.

The minimum distance to any neighboring device from another manufacturer is as follows:

￿vertical space of at least 100 mm (3.93 in.),

￿horizontal space of at least 20 mm (0.78 in.).

Minimum clearances for the XPSMF2DO801 safety remote output module (Compact Devices):

mm

inch

HIMatrix by HIMA

F3

HIMA

HIMatrix by HIMA

F31

HIMA

100

3.94

 

20

 

 

 

 

 

 

0.79

 

HIMatrix

by HIMA

by HIMA

 

F30

HIMatrix F3

HIMA

 

 

HIMA

Note: The installation must be performed so that

￿the device is not subject to heat emission from neighboring devices and

￿devices with high EMC interference do not affect the XPSMF2DO801.

Heat emission and electromagnetic compatibility (EMC) must be checked for devices from other manufacturers to ensure that operation of the remote output device is not affected by any external device.

The overall installation space for all cables must also be taken into account to ensure sufficient ventilation. Additional measures, such as installing heat extraction fans, can be taken if the product’s housing becomes warm.

14

33003405 07/2007

Image 14
Contents XPSMF2DO801 Remote Output Module Hardware Manual 07/2007Page Table of Contents Appendices At a GlanceImportant Information Safety InformationProcedure Safety Information About the Book At a Glance33003405 07/2007 Topic Overview XPSMF2DO801Overview Whats in this Chapter? Front View IntroductionRepresentation ModuleDimensions Dimensions Remote output moduleSide View Introduction InstallationProcedure Step ActionHIMatrix 100 Compact device Cable duct Spacer = H 40 mm / 1.57 Installation with spacersLength of the required spacer is calculated as follows = length of the spacer = height of the cable ductHIMatrix F31 Heat Case installation Calculation of a m2 1m2=10.76ft2 Convection HousingInternal Variable DescriptionTemperature State/Operating Temperature range Temperature stateOverview Application and Function Overview XPSMF2DO801 safety remote output moduleInitial Operation StageApplication Function Terminal No Designation Function relay output Application and Function Following will occur CableDisconnection SystemVoltage level Reaction of the controller Power Supply InterruptionLarge System Reconfiguration StepShort-Circuit Characteristics Output Channels SHORT-CIRCUIT ConditionModules Offline Proof Test Execution Periodic Proof TestingOffline Proof-Test Offline ProofWhats in this Equipment DescriptionOutput module Chapter?Elements of the front panel Housing ElementsXPSMF2DO801 safety remote output module Top View Following image shows the elements of the top panel Back Panel Following image shows elements of the back panel Housing, about 40...50 mm 1.57...1.97 in. from the left rim Reset ButtonUsing Reset ButtonCommunication Overview Safety-Related CommunicationCommunication via switches HIMatrix F3AIO Following scheme shows a SafeEthernet networking exampleNumber Following is a Ethernet cable connection diagramConnector pairs and cable distances Maximum cable distanceEquipment Description LEDs Color Status Meaning LED DescriptionFollowing table describes behaviors of the LEDs LED Interface WiringEthernet Wiring ElementsClass D capacity are required RJ45 ConnectorSwitches RecommendedBit numbers e.g IP Addressing and System IDDescription SafeEthernet 33003405 07/2007 Ethernet OperationParameters InterfacesUDP ports and usage Connections for SafeEthernet/ Networking ExamplesUsed Network Ports for Ethernet Communication TCP ports and usageOSI model For the next higher level and relies on the next lower levelFollowing table describes the seven OSI layers bottom-top Number Layer Data DescriptionConditions Operating ConditionsClimatic Following tables MechanicalEMC Conditions Equipment Description Power Supply Connectors Technical CharacteristicsMechanical Data Power Supply Connectors Signal Line ConnectorsStripping Length and Torque Relay Outputs Supply voltageItems Additional ItemsList of Additional Equipment Description Equipment Description Appendix? AppendicesAppendix contains the following chapters Chapter Chapter NameAppendices Connection Diagrams, Examples Application, and Error Codes Error Codes System signal MeaningBrief description of the functional devices Elements of the network Wiring ExamplesSafeEthernet Protocol Ethernet Wiring Example NetworkingBrief description of the functional devices Element Modbus serialFor setting the communication parameters proceed as follows Configuration of Ethernet InterfacesCommunication Settings Flow-Control Mode list, select AutonegParameters of a port configuration Konfiguration/Abl-Mode/HIMatrix F35/OMFollowing table contains the parameter descriptions Parameter DescriptionBrief description of the functional devices Glossary Field bus Functional block diagramFault tolerance time See FTTProtective extra low voltage Object linking and embeddingOSI Model Open system interconnection model Programmable electronic systemSafety integrity level according to IEC Safety extra low voltageSequential function chart System-rack-slotIndex Index