Schneider Electric XPSMF2DO801 manual Terminal No Designation Function relay output

Page 27

Application and Function

Safety-RelatedThe XPSMF2DO801 safety remote output module has eight relay outputs. Each

Relay Outputs relay output has its own LED to indicate the status of the output.

Each output of the module is fitted with two safety relays in diversity with positively guided contacts and one standard type relay. Internal fuses are used to limit the switching current of the output contacts to 60% (3.15 A) of the maximum admissible value (according to VDE 0116, En 298). The contact outputs can be used for safety shutdowns. For DC switching the contact circuit must be additionally equipped with an external fuse adapted to the maximum admissible current.

An output is in a safe state when it is de-energized. If a fault occurs, all outputs are switched off.

If the module has a fault all outputs are switched off. In the event of a fault at Ethernet communication the concerning output is set to the initial value. How the actuators respond in such a case should be taken into account.

Faults in one or more channels as well as a fault on the module are indicated by the FAULT LED on the front plate of the remote output module.

The relay outputs are connected to the following terminals:

Terminal No.	Designation		Function (relay output)

1	DO1		contact 1, terminal A

2			contact 1, terminal B

3	DO2		contact 2, terminal A

4			contact 2, terminal B

5	DO3		contact 3, terminal A

6			contact 3, terminal B

7	DO4		contact 4, terminal A

8			contact 4, terminal B

9	DO5		contact 5, terminal A

10			contact 5, terminal B

11	DO6		contact 6, terminal A

12			contact 6, terminal B

13	DO7		contact 7, terminal A

14			contact 7, terminal B

15	DO8		contact 8, terminal A

16			contact 8, terminal B

33003405 07/2007

27

Image 27

Contents 07/2007 XPSMF2DO801 Remote Output Module Hardware ManualPage Table of Contents At a Glance AppendicesSafety Information ProcedureImportant Information Safety Information At a Glance About the Book33003405 07/2007 Overview XPSMF2DO801 Overview Whats in this Chapter?Topic Module IntroductionRepresentation Front ViewDimensions Remote output module DimensionsSide View Step Action InstallationProcedure IntroductionHIMatrix 100 Compact device Cable duct Spacer = length of the spacer = height of the cable duct Installation with spacersLength of the required spacer is calculated as follows = H 40 mm / 1.57HIMatrix F31 Heat Case installation Calculation of a m2 1m2=10.76ft2 Variable Description HousingInternal ConvectionTemperature range Temperature state Temperature State/OperatingOverview Application and Function Stage XPSMF2DO801 safety remote output moduleInitial Operation OverviewApplication Function Terminal No Designation Function relay output Application and Function System CableDisconnection Following will occurStep Power Supply InterruptionLarge System Reconfiguration Voltage level Reaction of the controllerSHORT-CIRCUIT Condition Short-Circuit Characteristics Output ChannelsModules Offline Proof Test Offline Proof Periodic Proof TestingOffline Proof-Test ExecutionChapter? Equipment DescriptionOutput module Whats in thisHousing Elements XPSMF2DO801 safety remote output moduleElements of the front panel Top View Following image shows the elements of the top panel Back Panel Following image shows elements of the back panel Button Reset ButtonUsing Reset Housing, about 40...50 mm 1.57...1.97 in. from the left rimOverview Safety-Related Communication Communication via switchesCommunication Following scheme shows a SafeEthernet networking example HIMatrix F3AIOMaximum cable distance Following is a Ethernet cable connection diagramConnector pairs and cable distances NumberEquipment Description LEDs LED Description Following table describes behaviors of the LEDsColor Status Meaning LED Elements WiringEthernet Wiring InterfaceRecommended RJ45 ConnectorSwitches Class D capacity are requiredIP Addressing and System ID DescriptionBit numbers e.g SafeEthernet 33003405 07/2007 Interfaces OperationParameters EthernetTCP ports and usage Connections for SafeEthernet/ Networking ExamplesUsed Network Ports for Ethernet Communication UDP ports and usageFor the next higher level and relies on the next lower level OSI modelNumber Layer Data Description Following table describes the seven OSI layers bottom-topOperating Conditions ClimaticConditions Mechanical EMC ConditionsFollowing tables Equipment Description Signal Line Connectors Technical CharacteristicsMechanical Data Power Supply Connectors Power Supply ConnectorsStripping Length and Torque Supply voltage Relay OutputsAdditional Items List of AdditionalItems Equipment Description Equipment Description Chapter Chapter Name AppendicesAppendix contains the following chapters Appendix?Appendices Connection Diagrams, Examples Application, and Error Codes System signal Meaning Error CodesBrief description of the functional devices Networking Wiring ExamplesSafeEthernet Protocol Ethernet Wiring Example Elements of the networkBrief description of the functional devices Modbus serial ElementFlow-Control Mode list, select Autoneg Configuration of Ethernet InterfacesCommunication Settings For setting the communication parameters proceed as followsKonfiguration/Abl-Mode/HIMatrix F35/OM Parameters of a port configurationParameter Description Following table contains the parameter descriptionsBrief description of the functional devices Glossary See FTT Functional block diagramFault tolerance time Field busProgrammable electronic system Object linking and embeddingOSI Model Open system interconnection model Protective extra low voltageSystem-rack-slot Safety extra low voltageSequential function chart Safety integrity level according to IECIndex Index