Schneider Electric XPSMF2DO801 manual Following table contains the parameter descriptions

Page 75

		Brief description of the functional devices
	The following table contains the parameter descriptions:

	Parameter	Description

	Port	Port number, as assigned on device.
		Note: Only 1 configuration is possible per port.
		Value range 1...n, depending on the resource

	Speed [MBit/s]	The following selections are available:
		10 MBit/s data rate 10 MBit/s
		100 MBit/s data rate 100 MBit/s
		Autoneg (10/100) automatic setting of the baud rate
		The default setting is Autoneg.

	Flow control	The following selections are available:
		Full duplex communication in both directions at the same time
		Half duplex communication in one direction
		Autoneg automatic control of communication
		The default setting is Autoneg.

	Autoneg also with	The Advertising (transfer of Speed and Flow control properties) is
	fix values	made with fixed parameter values. Thereby other devices, whose port
		settings are Autoneg, can recognise how the PLC ports are set.

	Limit	Limit incoming Multicast and/or Broadcast packages.
		The following selections are available:
		Off no limit
		Broadcast limit Broadcast (128 kbit/s)
		Multicast and Broadcast limit Multicast and Broadcast (1024 kbit/s)
		The default setting is Broadcast.

Activation of Parameters are set in the COM window of the Hardware Management screen.

Settings Before the changes/settings become active the application program must be compiled using the Code Generator and then transferred to the PLC(s). The communication properties can be changed in the online mode using the Control Panel. The settings become active immediately, but are not transferred to the application program.

33003405 07/2007

75

Image 75

Contents 07/2007 XPSMF2DO801 Remote Output Module Hardware ManualPage Table of Contents At a Glance AppendicesSafety Information ProcedureImportant Information Safety Information At a Glance About the Book33003405 07/2007 Overview XPSMF2DO801 Overview Whats in this Chapter?Topic Module IntroductionRepresentation Front ViewDimensions Remote output module DimensionsSide View Step Action InstallationProcedure IntroductionHIMatrix 100 Compact device Cable duct Spacer = length of the spacer = height of the cable duct Installation with spacersLength of the required spacer is calculated as follows = H 40 mm / 1.57HIMatrix F31 Heat Case installation Calculation of a m2 1m2=10.76ft2 Variable Description HousingInternal ConvectionTemperature range Temperature state Temperature State/OperatingOverview Application and Function Stage XPSMF2DO801 safety remote output moduleInitial Operation OverviewApplication Function Terminal No Designation Function relay output Application and Function System CableDisconnection Following will occurStep Power Supply InterruptionLarge System Reconfiguration Voltage level Reaction of the controllerSHORT-CIRCUIT Condition Short-Circuit Characteristics Output ChannelsModules Offline Proof Test Offline Proof Periodic Proof TestingOffline Proof-Test ExecutionChapter? Equipment DescriptionOutput module Whats in thisHousing Elements XPSMF2DO801 safety remote output moduleElements of the front panel Top View Following image shows the elements of the top panel Back Panel Following image shows elements of the back panel Button Reset ButtonUsing Reset Housing, about 40...50 mm 1.57...1.97 in. from the left rimOverview Safety-Related Communication Communication via switchesCommunication Following scheme shows a SafeEthernet networking example HIMatrix F3AIOMaximum cable distance Following is a Ethernet cable connection diagramConnector pairs and cable distances NumberEquipment Description LEDs LED Description Following table describes behaviors of the LEDsColor Status Meaning LED Elements WiringEthernet Wiring InterfaceRecommended RJ45 ConnectorSwitches Class D capacity are requiredIP Addressing and System ID DescriptionBit numbers e.g SafeEthernet 33003405 07/2007 Interfaces OperationParameters EthernetTCP ports and usage Connections for SafeEthernet/ Networking ExamplesUsed Network Ports for Ethernet Communication UDP ports and usageFor the next higher level and relies on the next lower level OSI modelNumber Layer Data Description Following table describes the seven OSI layers bottom-topOperating Conditions ClimaticConditions Mechanical EMC ConditionsFollowing tables Equipment Description Signal Line Connectors Technical CharacteristicsMechanical Data Power Supply Connectors Power Supply ConnectorsStripping Length and Torque Supply voltage Relay OutputsAdditional Items List of AdditionalItems Equipment Description Equipment Description Chapter Chapter Name AppendicesAppendix contains the following chapters Appendix?Appendices Connection Diagrams, Examples Application, and Error Codes System signal Meaning Error CodesBrief description of the functional devices Networking Wiring ExamplesSafeEthernet Protocol Ethernet Wiring Example Elements of the networkBrief description of the functional devices Modbus serial ElementFlow-Control Mode list, select Autoneg Configuration of Ethernet InterfacesCommunication Settings For setting the communication parameters proceed as followsKonfiguration/Abl-Mode/HIMatrix F35/OM Parameters of a port configurationParameter Description Following table contains the parameter descriptionsBrief description of the functional devices Glossary See FTT Functional block diagramFault tolerance time Field busProgrammable electronic system Object linking and embeddingOSI Model Open system interconnection model Protective extra low voltageSystem-rack-slot Safety extra low voltageSequential function chart Safety integrity level according to IECIndex Index