Schneider Electric XPSMF2DO801 manual Index

Page 82

Index

M

maintenance, 33 mechanical conditions, 57 mechanical data, 59 Modbus TCP/IP, 53

mounting the remote output module, 14

O

operating conditions, 56

operation parameters of the Ethernet Interfaces, 52

OSI model, 54

P

power supply connectors, 59 power supply interruption, 30 procedure, 13

R

repair of remote output modules, 33 replacing faulty modules, 32 representation, 10

reset button, 39 RJ45 connector, 48

S

SafeEthernet, 50

SafeEthernet protocol wiring example, 70 SafeEthernet wiring, 47 SafeEthernet wiring example, 72 safety-related communication, 40 safety-related relay outputs, 27 short-circuit characteristics of the output channels, 31

signal line connectors, 59, 60 small system reconfiguration, 30 specified cables, 48

stripping length and torque, 60 supply voltage, 61 switches, 48

T

TCP/IP description, 49 technical characteristics, 59 technical data, 60

temperature state/operating temperature, 21 testing the inputs and outputs for interference voltage and earth faults, 32

U

using reset button, 39

V

voltage supply, 58

W

wiring, 47

wiring examples, 70

82	33003405 07/2007

Image 82

Contents XPSMF2DO801 Remote Output Module Hardware Manual 07/2007Page Table of Contents Appendices At a GlanceProcedure Safety InformationImportant Information Safety Information About the Book At a Glance33003405 07/2007 Overview Whats in this Chapter? Overview XPSMF2DO801Topic Front View IntroductionRepresentation ModuleDimensions Dimensions Remote output moduleSide View Introduction InstallationProcedure Step ActionHIMatrix 100 Compact device Cable duct Spacer = H 40 mm / 1.57 Installation with spacersLength of the required spacer is calculated as follows = length of the spacer = height of the cable ductHIMatrix F31 Heat Case installation Calculation of a m2 1m2=10.76ft2 Convection HousingInternal Variable DescriptionTemperature State/Operating Temperature range Temperature stateOverview Application and Function Overview XPSMF2DO801 safety remote output moduleInitial Operation StageApplication Function Terminal No Designation Function relay output Application and Function Following will occur CableDisconnection SystemVoltage level Reaction of the controller Power Supply InterruptionLarge System Reconfiguration StepShort-Circuit Characteristics Output Channels SHORT-CIRCUIT ConditionModules Offline Proof Test Execution Periodic Proof TestingOffline Proof-Test Offline ProofWhats in this Equipment DescriptionOutput module Chapter?XPSMF2DO801 safety remote output module Housing ElementsElements of the front panel Top View Following image shows the elements of the top panel Back Panel Following image shows elements of the back panel Housing, about 40...50 mm 1.57...1.97 in. from the left rim Reset ButtonUsing Reset ButtonCommunication via switches Overview Safety-Related CommunicationCommunication HIMatrix F3AIO Following scheme shows a SafeEthernet networking exampleNumber Following is a Ethernet cable connection diagramConnector pairs and cable distances Maximum cable distanceEquipment Description LEDs Following table describes behaviors of the LEDs LED DescriptionColor Status Meaning LED Interface WiringEthernet Wiring ElementsClass D capacity are required RJ45 ConnectorSwitches RecommendedDescription IP Addressing and System IDBit numbers e.g SafeEthernet 33003405 07/2007 Ethernet OperationParameters InterfacesUDP ports and usage Connections for SafeEthernet/ Networking ExamplesUsed Network Ports for Ethernet Communication TCP ports and usageOSI model For the next higher level and relies on the next lower levelFollowing table describes the seven OSI layers bottom-top Number Layer Data DescriptionClimatic Operating ConditionsConditions EMC Conditions MechanicalFollowing tables Equipment Description Power Supply Connectors Technical CharacteristicsMechanical Data Power Supply Connectors Signal Line ConnectorsStripping Length and Torque Relay Outputs Supply voltageList of Additional Additional ItemsItems Equipment Description Equipment Description Appendix? AppendicesAppendix contains the following chapters Chapter Chapter NameAppendices Connection Diagrams, Examples Application, and Error Codes Error Codes System signal MeaningBrief description of the functional devices Elements of the network Wiring ExamplesSafeEthernet Protocol Ethernet Wiring Example NetworkingBrief description of the functional devices Element Modbus serialFor setting the communication parameters proceed as follows Configuration of Ethernet InterfacesCommunication Settings Flow-Control Mode list, select AutonegParameters of a port configuration Konfiguration/Abl-Mode/HIMatrix F35/OMFollowing table contains the parameter descriptions Parameter DescriptionBrief description of the functional devices Glossary Field bus Functional block diagramFault tolerance time See FTTProtective extra low voltage Object linking and embeddingOSI Model Open system interconnection model Programmable electronic systemSafety integrity level according to IEC Safety extra low voltageSequential function chart System-rack-slotIndex Index