Schneider Electric XPSMF2DO801 manual Error Codes, System signal Meaning

Page 68

Brief description of the functional devices

Error Codes

Description of	The error codes listed in this section appear in XPSMFWIN programming
Error Codes	environment.
	The following table describes error codes of relay outputs:

System signal		R/W	Meaning

Module.SRS [UDINT]		R	slot number (System-Rack-Slot)

Module.Type [UINT]		R	type of module, setpoint: 0x003C [60dez]

Module.Error Code [WORD]		R	error codes of the module

			0x0000	I/O processing, may be faulty, see further error codes
			0x0001	no I/O processing (CPU not in RUN)
			0x0002	no I/O processing during start-up tests
			0x0004	manufacturer interface in operation
			0x0010	no I/O processing: incorrect configuration
			0x0020	no I/O processing: error rate exceeded
			0x0040	no I/O processing: configured module not inserted
			0x0080

DO.Error Code [WORD]		R	error codes of all digital outputs

			0x0001	module error
			0x0002	MEZ test, safety switch 1 failed
			0x0004	MEZ test, safety switch 2 failed
			0x0008	FTZ test of test pattern failed
			0x0010	MEZ test of readback channels failed
			0x0020	MEZ test, active disconnection failed
			0x0040	error with initialization: relays
			0x0080	FTZ test: error of relay voltage
			0x0100	FTZ test of CS (chip select) signals failed
			0x0400	FTZ test: 1. temperature threshold exceeded
			0x0800	FTZ test: 2. temperature threshold exceeded
			0x1000	MEZ test: status of safety switch 1
			0x2000	MEZ test: status of safety switches
			0x4000	MEZ test: active disconection by watchdog failed

68	33003405 07/2007

Image 68

Contents XPSMF2DO801 Remote Output Module Hardware Manual 07/2007Page Table of Contents Appendices At a GlanceImportant Information Safety InformationProcedure Safety Information About the Book At a Glance33003405 07/2007 Topic Overview XPSMF2DO801Overview Whats in this Chapter? Introduction RepresentationFront View ModuleDimensions Dimensions Remote output moduleSide View Installation ProcedureIntroduction Step ActionHIMatrix 100 Compact device Cable duct Spacer Installation with spacers Length of the required spacer is calculated as follows= H 40 mm / 1.57 = length of the spacer = height of the cable ductHIMatrix F31 Heat Case installation Calculation of a m2 1m2=10.76ft2 Housing InternalConvection Variable DescriptionTemperature State/Operating Temperature range Temperature stateOverview Application and Function XPSMF2DO801 safety remote output module Initial OperationOverview StageApplication Function Terminal No Designation Function relay output Application and Function Cable DisconnectionFollowing will occur SystemPower Supply Interruption Large System ReconfigurationVoltage level Reaction of the controller StepShort-Circuit Characteristics Output Channels SHORT-CIRCUIT ConditionModules Offline Proof Test Periodic Proof Testing Offline Proof-TestExecution Offline ProofEquipment Description Output moduleWhats in this Chapter?Elements of the front panel Housing ElementsXPSMF2DO801 safety remote output module Top View Following image shows the elements of the top panel Back Panel Following image shows elements of the back panel Reset Button Using ResetHousing, about 40...50 mm 1.57...1.97 in. from the left rim ButtonCommunication Overview Safety-Related CommunicationCommunication via switches HIMatrix F3AIO Following scheme shows a SafeEthernet networking exampleFollowing is a Ethernet cable connection diagram Connector pairs and cable distancesNumber Maximum cable distanceEquipment Description LEDs Color Status Meaning LED DescriptionFollowing table describes behaviors of the LEDs LED Wiring Ethernet WiringInterface ElementsRJ45 Connector SwitchesClass D capacity are required RecommendedBit numbers e.g IP Addressing and System IDDescription SafeEthernet 33003405 07/2007 Operation ParametersEthernet InterfacesConnections for SafeEthernet/ Networking Examples Used Network Ports for Ethernet CommunicationUDP ports and usage TCP ports and usageOSI model For the next higher level and relies on the next lower levelFollowing table describes the seven OSI layers bottom-top Number Layer Data DescriptionConditions Operating ConditionsClimatic Following tables MechanicalEMC Conditions Equipment Description Technical Characteristics Mechanical Data Power Supply ConnectorsPower Supply Connectors Signal Line ConnectorsStripping Length and Torque Relay Outputs Supply voltageItems Additional ItemsList of Additional Equipment Description Equipment Description Appendices Appendix contains the following chaptersAppendix? Chapter Chapter NameAppendices Connection Diagrams, Examples Application, and Error Codes Error Codes System signal MeaningBrief description of the functional devices Wiring Examples SafeEthernet Protocol Ethernet Wiring ExampleElements of the network NetworkingBrief description of the functional devices Element Modbus serialConfiguration of Ethernet Interfaces Communication SettingsFor setting the communication parameters proceed as follows Flow-Control Mode list, select AutonegParameters of a port configuration Konfiguration/Abl-Mode/HIMatrix F35/OMFollowing table contains the parameter descriptions Parameter DescriptionBrief description of the functional devices Glossary Functional block diagram Fault tolerance timeField bus See FTTObject linking and embedding OSI Model Open system interconnection modelProtective extra low voltage Programmable electronic systemSafety extra low voltage Sequential function chartSafety integrity level according to IEC System-rack-slotIndex Index