Barco R9002790 manual Safety Area around the Projector

Page 16

Installation Guidelines

Safety Area around the Projector

Make sure the projector is located so that the air inlets and outlets for the cooling system are not obstructed. Leave a safety area of about 1 meter on the left and the right side of the projector7825,$ .

\WLYDUJIRQ3

Safety area for blow out hot air

Image 6

Re-adjusting the lamp position in the lamp casing

With higher run times, the light output of the lamp will decrease, which results in a lower light output on the screen. This light output decrease can be compensated by readjusting the position of the lamp.

As the projector has to be opened, this procedure has to be performed by qualified service technician.. Handle as follow :

1On the side of the inputs, turn the retaining bolt a quarter counter clockwise.

2 Flip the cover to the left side and take off.

3.Start up the adjustment mode and select Service.

4.Select Lamp. The Z-axis indication (lamp menu in service mode) will be helpful while turning screw B (image 7).

5 Loosen the nut A (image 7) on the back of the lamp casing (nutdriver 10).

6 Adjust the screw B (image7) with an allen key by turning a little clockwise until the maximum light output is reached (the maximum value of the Z-AXIS indication on the lamp menu).

7 Fasten the nut on the back of the lamp casing to secure this position (nutdriver 10).

Image 7

3-4		R5976336 BARCOSLM R6 Executive 06092001

Image 16

Contents Barco Projection Systems SLM R6Barco n.v./Projection Systems Table of Contents Getting Started Random Access Adjustment Mode Installation Mode Standard Source SET UP Files Index R5976336 Barcoslm R6 Executive Safety Instruction Related to SLM Projectors To prevent battery explosionTo prevent personel injury To prevent projector damageExtra safety manual DefinitionsPackaging and Dimensions Dimensions Installation Guidelines Which configuration can be used Positioning the ProjectorInstallation Guidelines Safety Area around the Projector Re-adjusting the lamp position in the lamp casingAvailable lenses Which Lens has to be selectedLens formulas to calculate the projector distance Installing the Projection Lens How is the battery delivered ? Cleaning the lensHow to install ? AC Power mains cord connection Switching onConnections FusesSwitching to Stand-by Switching OffLamp Run Time Indication Lamp Runtime WarningInput facilities Input facilities, RCVDS05 or VS05 connectedInput module insertion into the projector Which signals can be connected to slot 1 & 2 ? Pin assignment for the DVI connectorHow to select input Slot 1 or Fixed Slot slot 1How to change the input slot setting Adjustment ModeInstallation Input SlotsWhat can be connected to this input ? How to select the Digital inputConnections HD SDI Digital Input slot 3 Set up of the Baud Rate for Communication with a Computer Connecting a Rcvds 05 to the projectorConnecting a VS05 to the projector Connecting an IR Remote Receiver to the projectorConnections Getting Started FunctionalityTerminology RCULamp Run Time Warning Temperature error DMD ErrorService Quick Language ChangeQuick Lens Adjustment Lens Adjustment ZOOM/FOCUSPointing to the reflective screen Quick On Screen Color changeOSD Color Highlighted Item Hardwired Remote Input Hardwired to the XLR InputWhy a projector address ? Set up an Individual Projector AddressHow to control the projector or projectors ? Before using the RCUHow to Program an Address into the RCU ? Display the Projector Address on the ScreenInput Selection PictureContolsPause key Stand-by keyStart UP of the Adjustment Mode PasswordProtectionEntering the Password Start upRemark Setting Up the personalised PasswordsMenus on Local LCD Display Overview Flowchart Random Access Adjustment ModeStarting up Connecting a new Source Start up the File ServicePossible File Manipulations File AnnotationHow to load a file ? Start up the Load FileImage is not perfect ? Load FileHow to start up the Edit menu ? Which items can be adjusted ?How to change the settings ? What can be done with the Edit File menu ?How to find the correct values for the displayed item? Edit File OptionsConfirm Edit File Rename FileHow to change the characters ? Copy FileFile Sort File LoadDelete File Confirm Delete FileHow to change the CTI setting ? What is CTI ?Picture Tuning Available color temperature Adjusting the Color TemperatureWhat can be adjusted ? Custom BalanceHow to change the Gamma Value ? What can be done ?How can it be selected ? PurposeWhy adjusting the input balance ? To change the noise reduction valueNoise Reduction Input BalanceHow to adjust the input balance for YUV input signals? Which geometry adjustments are possible ?How can an adjustment be adjusted ? To start up the Geometry functionsTo start up the size adjustment To start up the shift actionAdjusting the blanking Available Blanking AdjustmentBlanking Setting Up the Aspect Ratio What can be done?To view or to change the input configuration Possible results for the fixed input slots 1What can be installed ? What if a switcher is connected to the projector ?Defining the Output module of the RCVDS05 How to start up ? Defining the Infrared Communication protocolSet up the Correct Configuration How to change this color setting ?Changing the Shutdown Setting What will happenChanging the Background Color Changing the Shutdown TimeHow to select an internal pattern ? What can be done with these internal patterns ?How to shift the image ? How to Zoom/Focus ?Zoom/Focus/Shift How to get an overview ? OptionsHow to set up? Installation Mode Service Mode Built-up of the service modeInformation How to display the Identification screen ?Detailed description How to enable or disable the password function ? About password TypesAccess Control List How to change the password ?Access Control List Entering the new projector address How to change that address ?Start Up the Serial Communication menu Setting up the Baud rate Installing the Interface StandardAvailable Baud rates RS422 TerminationLamp information light output switching How to display the lamp menuHow to switch the constant light output ? How to add or the change the settings ?Available settings How to get add ins ?How to activate an add-in ? Available Add InsHow to select diagnosis ? What can be seen ?How to select ? How to select the overview ?I2C Diagnosis FormatterConfirm Quick Access Programmable Function KeysWhat can be done with these keys How can a Function Key be programmed ?10-2 R5976336 Barcoslm R6 Executive Standard Source SET UP Files Name Resolution Fvert Fhor Fpix Ptot Pact Ltot Lact KHZ MHZMuse Index RCU