Barco R9002790 manual Cleaning the lens, How is the battery delivered ?, How to install ?

Page 19

Installation Guidelines

Cleaning the lens

To minimize the possibility of damaging the optical coating or scratching exposed lens surface, we have developed recommendations for cleaning the lens. FIRST, we recommend you try to remove any material from the lens by blowing it off with clean, dry deionized air. DO NOT use any liquid to clean the lenses.

A TorayseeTM cloth is included with the lens kit.

Proceed as follows :

1.Always wipe lenses with a CLEAN TorayseeTM cloth.

2.Always wipe lenses in a single direction. Do not wipe back and forwards across the lens surface as this tends to grind dirt into the coating.

3.Do not leave cleaning cloth in either an open room or lab coat pocket, as doing so can contaminate the cloth.

4.If smears occur when cleaning lenses, replace the cloth. Smears are the first indication of a dirty cloth.

5.Do not use fabric softener when washing the cleaning cloth or softener sheets when drying the cloth.

6.Do not use liquid cleaners on the cloth as doing so will contaminate the cloth.

Order number for a new TorayseeTM cloth : R379058.

Battery installation in the RCU.

How is the battery delivered ?

A battery (not yet installed to save the battery life time) is delivered inside the plastic bag with the power cord.

How to install ?

To install the battery, remove the battery cover on the backside of the remote control by pushing the indicated handle a little towards the bottom of the RCU. Lift up the top side of the cover at the same time (fig. 18).

Insert the new 9 V battery (type E-block or equivalent) in the lower compartment and connect the battery to the contact plate. Insert the battery into the lower compartment and put the cover back.

Note :

Projector address has to be programmed on the RCU before using the RCU (see chapter 'Controlling').

Contact plate

D'5:Insert here the 'Insert card RCU' which you can cut out on the last page of this manual.

Battery

Image15

R5976336 BARCOSLM R6 Executive 06092001		3-7

Image 19

Contents SLM R6 Barco Projection SystemsBarco n.v./Projection Systems Table of Contents Getting Started Random Access Adjustment Mode Installation Mode Standard Source SET UP Files Index R5976336 Barcoslm R6 Executive To prevent projector damage Safety Instruction Related to SLM ProjectorsTo prevent battery explosion To prevent personel injuryDefinitions Extra safety manualPackaging and Dimensions Dimensions Installation Guidelines Positioning the Projector Which configuration can be usedInstallation Guidelines Re-adjusting the lamp position in the lamp casing Safety Area around the ProjectorAvailable lenses Which Lens has to be selectedLens formulas to calculate the projector distance Installing the Projection Lens How is the battery delivered ? Cleaning the lensHow to install ? Fuses AC Power mains cord connectionSwitching on ConnectionsLamp Runtime Warning Switching to Stand-bySwitching Off Lamp Run Time IndicationInput facilities, RCVDS05 or VS05 connected Input facilitiesInput module insertion into the projector Fixed Slot slot 1 Which signals can be connected to slot 1 & 2 ?Pin assignment for the DVI connector How to select input Slot 1 orInput Slots How to change the input slot settingAdjustment Mode InstallationWhat can be connected to this input ? How to select the Digital inputConnections HD SDI Digital Input slot 3 Connecting an IR Remote Receiver to the projector Set up of the Baud Rate for Communication with a ComputerConnecting a Rcvds 05 to the projector Connecting a VS05 to the projectorConnections Functionality Getting StartedRCU TerminologyLamp Run Time Warning Quick Language Change Temperature error DMDError ServiceLens Adjustment ZOOM/FOCUS Quick Lens AdjustmentPointing to the reflective screen Quick On Screen Color changeOSD Color Highlighted Item Hardwired to the XLR Input Hardwired Remote InputBefore using the RCU Why a projector address ?Set up an Individual Projector Address How to control the projector or projectors ?PictureContols How to Program an Address into the RCU ?Display the Projector Address on the Screen Input SelectionStand-by key Pause keyStart up Start UP of the Adjustment ModePasswordProtection Entering the PasswordRemark Setting Up the personalised PasswordsMenus on Local LCD Display Overview Flowchart Random Access Adjustment ModeStarting up File Annotation Connecting a new SourceStart up the File Service Possible File ManipulationsLoad File How to load a file ?Start up the Load File Image is not perfect ?What can be done with the Edit File menu ? How to start up the Edit menu ?Which items can be adjusted ? How to change the settings ?Edit File Options How to find the correct values for the displayed item?Rename File Confirm Edit FileCopy File How to change the characters ?Confirm Delete File File SortFile Load Delete FileHow to change the CTI setting ? What is CTI ?Picture Tuning Custom Balance Available color temperatureAdjusting the Color Temperature What can be adjusted ?Purpose How to change the Gamma Value ?What can be done ? How can it be selected ?Input Balance Why adjusting the input balance ?To change the noise reduction value Noise ReductionTo start up the Geometry functions How to adjust the input balance for YUV input signals?Which geometry adjustments are possible ? How can an adjustment be adjusted ?To start up the shift action To start up the size adjustmentAdjusting the blanking Available Blanking AdjustmentBlanking What can be done? Setting Up the Aspect RatioPossible results for the fixed input slots 1 To view or to change the input configurationWhat can be installed ? What if a switcher is connected to the projector ?Defining the Output module of the RCVDS05 Defining the Infrared Communication protocol How to start up ?How to change this color setting ? Set up the Correct ConfigurationChanging the Shutdown Time Changing the Shutdown SettingWhat will happen Changing the Background ColorWhat can be done with these internal patterns ? How to select an internal pattern ?How to shift the image ? How to Zoom/Focus ?Zoom/Focus/Shift Options How to get an overview ?How to set up? Installation Mode Built-up of the service mode Service ModeInformation How to display the Identification screen ?Detailed description About password Types How to enable or disable the password function ?Access Control List How to change the password ?Access Control List Entering the new projector address How to change that address ?Start Up the Serial Communication menu RS422 Termination Setting up the Baud rateInstalling the Interface Standard Available Baud ratesHow to add or the change the settings ? Lamp information light output switchingHow to display the lamp menu How to switch the constant light output ?Available Add Ins Available settingsHow to get add ins ? How to activate an add-in ?What can be seen ? How to select diagnosis ?Formatter How to select ?How to select the overview ? I2C DiagnosisHow can a Function Key be programmed ? Confirm Quick AccessProgrammable Function Keys What can be done with these keys10-2 R5976336 Barcoslm R6 Executive Name Resolution Fvert Fhor Fpix Ptot Pact Ltot Lact KHZ MHZ Standard Source SET UP FilesMuse Index RCU