Barco R9002790 Temperature error DMD, Quick Language Change, Error, Service, Change Language

Page 33

Getting Started

Lamp Light Output Indication

When starting up and the center lumens measurement is lower than 50 % of its initial value, the lamp light output warning will be displayed for 1 minute. Press ENTER to continue. The message will not be repeated during operation.

WARNING

Lamp run time is 1400 hours.

The light output of the lamp is less

than 50% of its initial value.

It is advisable to replace the lamp

before damage occurs.

<ENTER> to confirm

When the 'Constant Light Ouput' (CLO) options is installed, the light output message will appear on the screen when the light output is reduced with 33% from its initial value.

This message will be repeated every hour.

Switching to Stand-by.

When the projector is running and you want to go to stand-by, press the stand-by key.

Switching Off

To switch off:

-First press STANDBY key and let the projector cool down until the fans stopblowing, or at least 15 min.

-Switch off the projector with the power switch.

Temperature error DMD

When the temperature of one of the DMD is too low or too high the projector will be switched automatically to standby. Before switching to standby, the following message appears for 3 seconds on the screen : 'DMD out of operating temperature range. Automatic shutdown is activated.'.

A '-t' appears on the LED display to indicate the user that the projector is switched to standby due to DMD temperature problems.

ERROR

DMD out of operating temperature

range.

Automatic shutdown is activated

Quick Set Up Adjustments

Quick Language Change

Only if different on screen languages are available, follow the next procedure to change the on screen language.

1Press ENTER to start up the adjustment mode.

2Press the cursor key or to highlight 'Service' (menu 1). When password protected, your password will be asked.

(more explanation about access by password can be found in Chapter 'Start up the Adjustment mode'.

3Press ENTER to display the Service mode menu.

3Push the cursor key or to highlight 'Change Language' (menu 2). If not visible in the menu, highlight first 'More' and press ENTER to display a second service menu. Select then 'Change Language'.

4Press ENTER to display the language selection menu.

5Push the cursor key or to highlight the desired language (menu 3).

For the moment, only English is available.

ADJUSTMENT MODE

Select a path from below :

RANDOM ACCESS

INSTALLATION

SERVICE

Select with or

then <ENTER> <EXIT> to return.

menu1

SERVICE

IDENTIFICATION

CHANGE PASSWORD CHANGE LANGUAGE CHANGE PROJ. ADDRESS SERIAL COMMUNICATION LAMP

MORE..

Select with or

then <ENTER>

<EXIT> to return.

menu2

CHANGE LANGUAGE

English

Select with or

then <ENTER>

<EXIT> to return.

menu3

5-4

 

R5976336 BARCOSLM R6 Executive 06092001

 

Page 32 Page 34
Image 33
Page 32 Page 34
Contents SLM R6 Barco Projection SystemsBarco n.v./Projection Systems Table of Contents Getting Started Random Access Adjustment Mode Installation Mode Standard Source SET UP Files Index R5976336 Barcoslm R6 Executive To prevent battery explosion Safety Instruction Related to SLM ProjectorsTo prevent personel injury To prevent projector damageDefinitions Extra safety manualPackaging and Dimensions Dimensions Installation Guidelines Positioning the Projector Which configuration can be usedInstallation Guidelines Re-adjusting the lamp position in the lamp casing Safety Area around the ProjectorWhich Lens has to be selected Available lensesLens formulas to calculate the projector distance Installing the Projection Lens Cleaning the lens How is the battery delivered ?How to install ? Switching on AC Power mains cord connectionConnections FusesSwitching Off Switching to Stand-byLamp Run Time Indication Lamp Runtime WarningInput facilities, RCVDS05 or VS05 connected Input facilitiesInput module insertion into the projector Pin assignment for the DVI connector Which signals can be connected to slot 1 & 2 ?How to select input Slot 1 or Fixed Slot slot 1Adjustment Mode How to change the input slot settingInstallation Input SlotsHow to select the Digital input What can be connected to this input ?Connections HD SDI Digital Input slot 3 Connecting a Rcvds 05 to the projector Set up of the Baud Rate for Communication with a ComputerConnecting a VS05 to the projector Connecting an IR Remote Receiver to the projectorConnections Functionality Getting StartedRCU TerminologyLamp Run Time Warning Error Temperature error DMDService Quick Language ChangeLens Adjustment ZOOM/FOCUS Quick Lens AdjustmentQuick On Screen Color change Pointing to the reflective screenOSD Color Highlighted Item Hardwired to the XLR Input Hardwired Remote InputSet up an Individual Projector Address Why a projector address ?How to control the projector or projectors ? Before using the RCUDisplay the Projector Address on the Screen How to Program an Address into the RCU ?Input Selection PictureContolsStand-by key Pause keyPasswordProtection Start UP of the Adjustment ModeEntering the Password Start upSetting Up the personalised Passwords RemarkMenus on Local LCD Display Random Access Adjustment Mode Overview FlowchartStarting up Start up the File Service Connecting a new SourcePossible File Manipulations File AnnotationStart up the Load File How to load a file ?Image is not perfect ? Load FileWhich items can be adjusted ? How to start up the Edit menu ?How to change the settings ? What can be done with the Edit File menu ?Edit File Options How to find the correct values for the displayed item?Rename File Confirm Edit FileCopy File How to change the characters ?File Load File SortDelete File Confirm Delete FileWhat is CTI ? How to change the CTI setting ?Picture Tuning Adjusting the Color Temperature Available color temperatureWhat can be adjusted ? Custom BalanceWhat can be done ? How to change the Gamma Value ?How can it be selected ? PurposeTo change the noise reduction value Why adjusting the input balance ?Noise Reduction Input BalanceWhich geometry adjustments are possible ? How to adjust the input balance for YUV input signals?How can an adjustment be adjusted ? To start up the Geometry functionsTo start up the shift action To start up the size adjustmentAvailable Blanking Adjustment Adjusting the blankingBlanking What can be done? Setting Up the Aspect RatioPossible results for the fixed input slots 1 To view or to change the input configurationWhat if a switcher is connected to the projector ? What can be installed ?Defining the Output module of the RCVDS05 Defining the Infrared Communication protocol How to start up ?How to change this color setting ? Set up the Correct ConfigurationWhat will happen Changing the Shutdown SettingChanging the Background Color Changing the Shutdown TimeWhat can be done with these internal patterns ? How to select an internal pattern ?How to Zoom/Focus ? How to shift the image ?Zoom/Focus/Shift Options How to get an overview ?How to set up? Installation Mode Built-up of the service mode Service ModeHow to display the Identification screen ? InformationDetailed description About password Types How to enable or disable the password function ?How to change the password ? Access Control ListAccess Control List How to change that address ? Entering the new projector addressStart Up the Serial Communication menu Installing the Interface Standard Setting up the Baud rateAvailable Baud rates RS422 TerminationHow to display the lamp menu Lamp information light output switchingHow to switch the constant light output ? How to add or the change the settings ?How to get add ins ? Available settingsHow to activate an add-in ? Available Add InsWhat can be seen ? How to select diagnosis ?How to select the overview ? How to select ?I2C Diagnosis FormatterProgrammable Function Keys Confirm Quick AccessWhat can be done with these keys How can a Function Key be programmed ?10-2 R5976336 Barcoslm R6 Executive Name Resolution Fvert Fhor Fpix Ptot Pact Ltot Lact KHZ MHZ Standard Source SET UP FilesMuse Index RCU
Top Page Image Contents