Barco LX-5 instruction manual Rear

Page 11

LX-5_EN.book Page 11 Friday, July 4, 2008 9:35 AM

Rear

G H I J K

R Q

P

DVI 1
DVI 2
CONTROL
USB
DVI 3
LAN
	OPERATE I/B STANDBY/ON
	LAMP
DVI 4	WARNING
RS-232C

Exhaust air

O N M L

G[DVI 1 to 4] Terminal

This is an input terminal for video signals. Connect it to the video output terminal of the computer.

(A Page 19, 21)

M[LAMP] Indicator

This indicator lights up in yellow when the lamp time exceeds 1400 hours.

NOTE:

HVent Hole

Warm air exits from the hole after cooling the projector.

CAUTION:

●Do not block the vent holes with papers, cloth, or soft cushions. Doing so may cause heat to trap inside the projector and result in fire or malfunction.

IVent Hole (For Lamp)

Warm air exits from the hole after cooling the lamp.

JMain Power Supply Switch

Use this to turn ON/OFF the main power supply of the projector unit.

KAC Power Input Terminal

Connect the supplied cord to this terminal.

●For details on indicator displays during warnings, refer to “Warnings Using Indicators”. (A Page 47)

●A lamp life message appears when the lamp time has exceeded 1500 hours. (A Page 46)

N[WARNING] Indicator

This indicator lights up in red when abnormality occurs on this projector. For details, refer to “Warnings Using Indicators”. (A Page 47)

O[OPERATE I/B ] Button

Pressing this button for one second or longer when in the standby mode (main power supply is ON) turns on the power of the projector unit. Pressing it for one second or longer when the power is ON switches the projector to the standby mode.

L[STANDBY/ON] Indicator

Lit (Red)	: When in the standby mode.
Lit (Green)	: When power is supplied.
Blinking (Red)	: When cooling down (cool down
	mode). (A Page 29)

Blinking (Green) : When the projected image is temporarily hidden. (A Page 29)

P[RS-232C]Terminal

This is the RS-232C interface-specific terminal. This projector can be controlled by connecting it to a computer using a RS-232C cable.

Q[LAN] Terminal

Enables control of this projector using a computer that is connected to the network.

NOTE:

●For details on indicator displays during warnings, refer to “Warnings Using Indicators”. (A Page 47)

R[USB] Terminal

Enables control of this projector by connecting it to a computer.

11

Image 11

Contents Lens is optional For Customer useMachine Noise Information Germany only Safety PrecautionsAbout the installation place Do not allow any unqualified person to install the unit Neutral Safety Precautions Cont’dPower cord Do not cut off the main plug from this equipmentEMC Supplement Contents User-friendly interface and high operability FeaturesHigh flexible installation Accessories Sold Separately AccessoriesViewing Conditions Brightness of Room Precautions During UseMaintenance Procedures Burning-in of D-ILA DeviceFront/Right Side Names and Functions of PartsRear Minimum Space Required InstallationOptional projection lens Projector Installation Angle Installing the Projector and ScreenLXD 11 Short focal length lens Installing the Projector and Screen Cont’d When shift amount in the left/right direction is 0 % When shift amount in the left direction is -50 %Projecting images by arranging projectors side by side When light passes through the glass of projection boothApprox .03 m Installing the Projector Screen Cont’dScreen Size and Projection Distance LXD 1.5 1.9 Zoom lens LXD 11 Short focal length lens Possible Input Signals and Projected Image Connecting Video Signals of the ComputerConnection During Single-Screen Mode Display Connection During Single-Screen Mode Display Connection During Two-Screen/Four Screen Mode Display Connecting Video Signals Computer Cont’d Connection Example During Four-Screen Mode Connection Example During Two-Screen Mode When assigning IP address from the Dhcp server Connection Using a LAN CableSpecifications of PC for Controlling this Projector When assigning a static IP addressIs not attached Turning On the Main PowerAssigning a static IP address IP Address Settings IP address setting at the computer Default GatewayDeselect the check Select AEnableB Assigning a static IP address Cont’d Cont’dAssigning IP Address from the Dhcp Server Using the Mail Delivery FeatureAfter connecting, turn on the main power Set the Adhcp ClientB setting of this projector to AdhcpbProjecting Image Useful Features During Projection Main Menu Setting Menu Cont’dTemperature Setting Value Description PowerLatest Error Signal StatusImage Menu Display Mode Setting MenuSetting Value Description Input Level Image Green color value is fixed Setting Value Description RedConvergence Menu Shift This menu is used for adjusting the projection lensLens Menu FocusOption Menu Network Menu Mail Menu Error message sent from this projectorSmtp Server Setting Value Description Mail SettingMail AddressRS-232C Interface Communication SpecificationsCommand Format ON/OFF External control command table Parameters used for the data format Cleaning and Replacing the Filter MaintenanceRoutine Servicing Replacement of Light Source LampTroubleshooting Image is Mode displayImmediately After power is Turned on Screen does Immediately When Projection has EndedOut of Range What to do when these messages are displayedMessage Cause Details Lamp Time OverCheck Measure Indicators Measures when the warning mode appears Indicator DescriptionLatest Error Specifications Pin Assignment Specifications Cont’dRS-232C Terminal Pin No Signal Operation Signal Direction DVI-D Terminal Pin No Signal Front Rear Dimensional Outline Drawing Top SideProjector