Barco LX-5 instruction manual Turning On the Main Power, Is not attached

Page 23

LX-5_EN.book Page 23 Friday, July 4, 2008 9:35 AM

Turning On the Main

Power

1 Check to ensure that this projector, computer, and switching hub are properly connected 2 Connect the power cord to the power input terminal of this projector

Power Cord

CAUTION:

 

 

(Supplied)

Do not connect the power cord when a lens (optional)

 

is not attached.

2 3

5

3 Insert plug into the power outlet on the wall 4 Remove the lens cap

5 Turn on the main power of the projector to set to [I]

The [STANDBY/ON], [LAMP], and [WARNING] indicators light up for about 45 seconds, after which the [STANDBY/ON] indicator turns red.

NOTE:

The default IP address of all LX-5is “192.168.0.2”. If multiple units of LX-5are used on the same network, do not turn on the main power of more than one projector unit at the same time. Doing so will result in duplication of the IP address, and thereby preventing proper access.

When using multiple units of LX-5,turn on the main power of the second unit and configure accordingly only after configuration of the first unit is complete. Configure subsequent units using the same procedure.

When duplication occurs in the IP address, make sure that only one unit of LX-5is connected on the same network (turn off the main power of the other LX-5units). Allow a time interval of at least 10 minutes before accessing. If access fails, turn off the power of all network equipments on the same network, followed by turning them on again.

23

Image 23
Contents Lens is optional For Customer useMachine Noise Information Germany only Safety PrecautionsAbout the installation place Do not allow any unqualified person to install the unit Neutral Safety Precautions Cont’dPower cord Do not cut off the main plug from this equipmentEMC Supplement Contents User-friendly interface and high operability FeaturesHigh flexible installation Accessories Sold Separately AccessoriesViewing Conditions Brightness of Room Precautions During UseMaintenance Procedures Burning-in of D-ILA DeviceFront/Right Side Names and Functions of PartsRear Minimum Space Required InstallationOptional projection lens Projector Installation Angle Installing the Projector and ScreenLXD 11 Short focal length lens Installing the Projector and Screen Cont’d When shift amount in the left/right direction is 0 %  When shift amount in the left direction is -50 %Projecting images by arranging projectors side by side  When light passes through the glass of projection boothApprox .03 m Installing the Projector Screen Cont’dScreen Size and Projection Distance  LXD 1.5 1.9 Zoom lens LXD 11 Short focal length lens  Possible Input Signals and Projected Image Connecting Video Signals of the ComputerConnection During Single-Screen Mode Display  Connection During Single-Screen Mode Display Connection During Two-Screen/Four Screen Mode Display Connecting Video Signals Computer Cont’d Connection Example During Four-Screen Mode  Connection Example During Two-Screen Mode When assigning IP address from the Dhcp server Connection Using a LAN CableSpecifications of PC for Controlling this Projector  When assigning a static IP addressIs not attached Turning On the Main PowerAssigning a static IP address IP Address Settings IP address setting at the computer Default GatewayDeselect the check Select AEnableB Assigning a static IP address Cont’d Cont’dAssigning IP Address from the Dhcp Server Using the Mail Delivery FeatureAfter connecting, turn on the main power Set the Adhcp ClientB setting of this projector to AdhcpbProjecting Image Useful Features During Projection Main Menu Setting Menu Cont’dTemperature Setting Value Description PowerLatest Error Signal StatusImage Menu Display Mode Setting MenuSetting Value Description Input Level Image Green color value is fixed Setting Value Description RedConvergence Menu Shift This menu is used for adjusting the projection lensLens Menu FocusOption Menu Network Menu Mail Menu  Error message sent from this projectorSmtp Server Setting Value Description Mail SettingMail AddressRS-232C Interface Communication SpecificationsCommand Format ON/OFF  External control command table Parameters used for the data format Cleaning and Replacing the Filter MaintenanceRoutine Servicing Replacement of Light Source LampTroubleshooting Image is Mode displayImmediately After power is Turned on Screen does Immediately When Projection has EndedOut of Range What to do when these messages are displayedMessage Cause Details Lamp Time OverCheck Measure Indicators Measures when the warning mode appears Indicator DescriptionLatest Error Specifications  Pin Assignment Specifications Cont’dRS-232C Terminal Pin No Signal Operation Signal Direction DVI-D Terminal Pin No Signal Front  Rear Dimensional Outline Drawing Top  SideProjector