Barco LX-5 instruction manual Specifications

Page 49

LX-5_EN.book Page 49 Friday, July 4, 2008 9:35 AM

Specifications

 General

Power supply

AC 110 V to 120 V,

 

AC 200 V to 240 V 50/60 Hz

Power consumption

1230 W (Standby mode: 2.7 W)

Current consumption Max 10.9 A (AC 110 V to 120 V) Max 6 A (AC 200 V to 240 V)

Calorific power

4428 kJ/h (1058 kcal/h)

Air capacity

Intake: Approx. 3 m³/min

 

Discharge: Approx. 3 m³/min

Allowable operating temperature range 10C to 35C

Allowable operating humidity range

Less than 80 % (no condensation)

Allowable storage temperature range –5C to 60C

Installation height

Operation guarantee: 2000 m and

 

below

 

Performance guarantee: 1500 m

 

and below

Dimensions (WidthDepthHeight)

663 mm803 mm342 to 362 mm

 

(Excluding lens, and small

 

protrusions)

Mass

56 kg (Excluding lens)

Optical System

Projection method

D-ILAanalog drive system 3

D-ILAelement *1, *2

1.27" (40962400 pixels) 3 pcs

 

(total no. of pixels: 29,491,200 pixels)

Projection lens

LXD(1.5 - 1.9)

(optional)

(1.50:1 to 1.84:1 zoom lens)

 

LXD(1:1)

 

(1:1.1 Short focal length lens)

Light-source Lamp

825 W xenon lamp

Screen size

80" to 300" (zoom lens)

 

50" to 250" (Short focal length lens)

Projection distance

Approx. 2.6 m to 12 m (zoom lens)

 

Approx. 1.2 m to 6 m

 

(Short focal length lens)

Signal System

Digital video

40962400,

Input format

40962160,

 

38402400,

38402160,

20481200,

20481080,

19201200,

19201080,

16001200,

12801024,

1024768,

800600,

640480

DVI clock

to 165

MHz (Single)

(Rx clock)

to 330

MHz (Dual)

Display resolution

40962400

Terminal

Video input

DVI-D (dual link) 24 pins

 

(supports 12-bit extended input)  4

 

(supports HDCP*3)

LAN

RJ45  1

USB

Type B (Slave)  1

RS-232C

D-sub 9 pins (male)  1

Accessories

Power cord (A Page 8)

Warranty card

*1 D-ILAis the abbreviation for Direct drive Image Light Amplifier.

*2 D-ILAdevices are manufactured using extremely high- precision technology. Pixel effectiveness is 99.99 %. Only 0.01 % or less of the pixels would either not lit up or remain permanently lit up.

*3 HDCP is the abbreviation for High-bandwidth Digital Content Protection system. Images from the DVI input terminal may not be displayed due to HDCP specification changes.

Specifications and appearance of this product may be subject to change for improvement without prior notice.

Please note that some of the pictures and illustrations may have been abridged, enlarged or contextualized in order to aid comprehension. Images may differ from the actual product.

49

Image 49
Contents Lens is optional For Customer useAbout the installation place Safety PrecautionsMachine Noise Information Germany only Do not allow any unqualified person to install the unit Power cord Safety Precautions Cont’dDo not cut off the main plug from this equipment NeutralEMC Supplement Contents High flexible installation FeaturesUser-friendly interface and high operability Accessories Sold Separately AccessoriesMaintenance Procedures Precautions During UseBurning-in of D-ILA Device Viewing Conditions Brightness of RoomFront/Right Side Names and Functions of PartsRear Optional projection lens InstallationMinimum Space Required Projector Installation Angle Installing the Projector and Screen When shift amount in the left/right direction is 0 % Installing the Projector and Screen Cont’d When shift amount in the left direction is -50 % LXD 11 Short focal length lensProjecting images by arranging projectors side by side  When light passes through the glass of projection boothScreen Size and Projection Distance Installing the Projector Screen Cont’d LXD 1.5 1.9 Zoom lens Approx .03 m LXD 11 Short focal length lens Connection During Single-Screen Mode Display Connecting Video Signals of the Computer Possible Input Signals and Projected Image  Connection During Single-Screen Mode Display Connection During Two-Screen/Four Screen Mode Display Connecting Video Signals Computer Cont’d Connection Example During Four-Screen Mode  Connection Example During Two-Screen ModeSpecifications of PC for Controlling this Projector Connection Using a LAN Cable When assigning a static IP address  When assigning IP address from the Dhcp serverIs not attached Turning On the Main Power IP address setting at the computer IP Address SettingsDefault Gateway Assigning a static IP addressDeselect the check Select AEnableB Assigning a static IP address Cont’d Cont’dAfter connecting, turn on the main power Using the Mail Delivery FeatureSet the Adhcp ClientB setting of this projector to Adhcpb Assigning IP Address from the Dhcp ServerProjecting Image Useful Features During Projection Main Menu Setting Menu Cont’dLatest Error Setting Value Description PowerSignal Status TemperatureImage Menu Setting Value Description Input Level Setting MenuDisplay Mode Convergence Menu Setting Value Description RedImage Green color value is fixed Lens Menu This menu is used for adjusting the projection lensFocus ShiftOption Menu Network Menu Mail Menu  Error message sent from this projectorMail Setting Value Description Mail SettingAddress Smtp ServerCommand Format Communication SpecificationsRS-232C Interface  Parameters used for the data format  External control command tableON/OFF Cleaning and Replacing the Filter MaintenanceRoutine Servicing Replacement of Light Source LampTroubleshooting Immediately After power is Turned on Screen does Mode displayImmediately When Projection has Ended Image isMessage Cause Details What to do when these messages are displayedLamp Time Over Out of Range Measures when the warning mode appears IndicatorsIndicator Description Check MeasureLatest Error Specifications RS-232C Terminal Pin No Signal Operation Signal Direction Specifications Cont’dDVI-D Terminal Pin No Signal  Pin Assignment Top Dimensional Outline Drawing Side  Front  RearProjector