Barco LX-5 instruction manual Useful Features During Projection

Page 29

LX-5_EN.book Page 29 Friday, July 4, 2008 9:35 AM

5 Adjust the focus

You can adjust the focus using the AFocusB item of the Lens menu.

To move the focus point closer:

Press the A+B (Near) end of AFocusB

To move the focus point away:

Press the A B (Far) end of AFocusB

NOTE:

The focus changes each time you click on the inner buttons (/). (Fine control)

The outer buttons ( / ) change the focus when they are depressed. (Coarse control)

6 Select a screen mode for projection

You can specify the screen mode using ADisplay ModeB of the Setting menu. (A Page 33)

8 Turn the main power at the rear of the projector unit to off [O]

The [STANDBY/ON] indicator on the projector unit goes off.

CAUTION:

Do not turn off the main power supply switch when in the cool down mode. Doing so may shorten the lamp life and cause a malfunction.

Upon using, attach the lens cap to prevent soiling of the lens.

When the projector is not to be used for a long time, disconnect the power plug.

Useful Features During Projection

Hiding the projected image temporarily

Main

Image

Setting

host PJ-1 user: root

Logout

Input Level

Standard Enhanced

Display Mode

The projected image can be hidden by clicking the AONB button under the AHideB item of the Image menu.

When the image is not displayed, pressing AOFFB under the AHideB item to display the hidden image.

Convergence

Lens

Option

Network

Mail

1 2

1

1

3

3 4

Main

Image

Setting

Convergence

Lens

host PJ-1 user: root

 

 

 

Logout

Brightness

 

 

 

Red

-30

0

+30

 

 

 

Green

-30

0

+30

 

 

 

Blue

-30

0

+30

 

 

 

NOTE:

The projected image varies according to the mode of connection. (A Page 19, 21)

7 Click the AOFFB button under the APowerB item of the Main menu to end the projection

Option

Network

Mail

Contrast

 

 

 

 

 

 

Red

-30

0

+30

 

 

 

 

 

 

 

Green

-30

0

+30

 

 

 

 

 

 

 

Blue

-30

0

+30

 

 

 

 

 

 

Gamma

 

 

 

Hide

 

A

B

C

 

OFF

ON

A gray image will be displayed for a few minutes during the ending process. When the process ends the projector switches to the cool down mode, and the [STANDBY/ON] indicator appears blinking in red.

After exiting the cool down mode, the projector switches automatically to the standby mode, and the [STANDBY/ON] indicator lights up in red.

You can also turn off the power by pressing the [OPERATE I/B] button on the projector unit for more than one second.

Cool down mode

The cool down mode is a function that cools down the lamp for an interval of about 180 seconds after projection ends (ending process).

This function is to prevent deformation and damage of the internal components of the projector due to heat from the overheated lamp. It also prevents lamp breakage and shortened lamp life.

When the projector is in the cool down mode, the [STANDBY/ON] indicator appears blinking in red.

Do not shut down the main power supply or unplug the power cord when in the cool down mode. Also, do not block the air inlets and vent holes. Doing so may shorten the lamp life and cause a malfunction.

NOTE:

When the image is hidden, the [STANDBY/ON] indicator appears blinking in green.

29

Image 29
Contents Lens is optional For Customer useMachine Noise Information Germany only Safety PrecautionsAbout the installation place Do not allow any unqualified person to install the unit Power cord Safety Precautions Cont’dDo not cut off the main plug from this equipment NeutralEMC Supplement Contents User-friendly interface and high operability FeaturesHigh flexible installation Accessories Sold Separately AccessoriesMaintenance Procedures Precautions During UseBurning-in of D-ILA Device Viewing Conditions Brightness of RoomFront/Right Side Names and Functions of PartsRear Minimum Space Required InstallationOptional projection lens Projector Installation Angle Installing the Projector and Screen When shift amount in the left/right direction is 0 % Installing the Projector and Screen Cont’d When shift amount in the left direction is -50 % LXD 11 Short focal length lensProjecting images by arranging projectors side by side  When light passes through the glass of projection boothScreen Size and Projection Distance Installing the Projector Screen Cont’d LXD 1.5 1.9 Zoom lens Approx .03 m LXD 11 Short focal length lens  Possible Input Signals and Projected Image Connecting Video Signals of the ComputerConnection During Single-Screen Mode Display  Connection During Single-Screen Mode Display Connection During Two-Screen/Four Screen Mode Display Connecting Video Signals Computer Cont’d Connection Example During Four-Screen Mode  Connection Example During Two-Screen ModeSpecifications of PC for Controlling this Projector Connection Using a LAN Cable When assigning a static IP address  When assigning IP address from the Dhcp serverIs not attached Turning On the Main Power IP address setting at the computer IP Address SettingsDefault Gateway Assigning a static IP addressDeselect the check Select AEnableB Assigning a static IP address Cont’d Cont’dAfter connecting, turn on the main power Using the Mail Delivery FeatureSet the Adhcp ClientB setting of this projector to Adhcpb Assigning IP Address from the Dhcp ServerProjecting Image Useful Features During Projection Main Menu Setting Menu Cont’dLatest Error Setting Value Description PowerSignal Status TemperatureImage Menu Display Mode Setting MenuSetting Value Description Input Level Image Green color value is fixed Setting Value Description RedConvergence Menu Lens Menu This menu is used for adjusting the projection lensFocus ShiftOption Menu Network Menu Mail Menu  Error message sent from this projectorMail Setting Value Description Mail SettingAddress Smtp ServerRS-232C Interface Communication SpecificationsCommand Format ON/OFF  External control command table Parameters used for the data format Cleaning and Replacing the Filter MaintenanceRoutine Servicing Replacement of Light Source LampTroubleshooting Immediately After power is Turned on Screen does Mode displayImmediately When Projection has Ended Image isMessage Cause Details What to do when these messages are displayedLamp Time Over Out of Range Measures when the warning mode appears IndicatorsIndicator Description Check MeasureLatest Error Specifications RS-232C Terminal Pin No Signal Operation Signal Direction Specifications Cont’dDVI-D Terminal Pin No Signal  Pin Assignment Top Dimensional Outline Drawing Side  Front  RearProjector