Meridian America D-ILA 1080MF1 Rear & Right Side, Handling the Control Panel Cover, Exhaust Vent

Page 10

Rear & Right Side

D	E F	G	H
SCREEN TRIGGER	SERVICE	RS-232C	DVI

B

Removing the control panel cover

Release	C
Release
Lock	A
	A
A Control Panel Cover	E Screen Trigger socket
Remove this cover when operating this unit or	This socket is used for controlling a motorised
when replacing the lamp unit.	screen. An output at DC +12 V/100 mA (max.)
• Unlock the cover, followed by sliding it down-	is produced when the power is on.
wards to remove it.	• Consult a qualified technician for a connection
• Please refer to page 11 for details on the con-	with the screen.
trol panel.

Handling the Control Panel Cover

•The gap between the body of the unit and the control panel cover is narrow. Be careful not to stick your finger into the gap between the body of the unit and the control panel cover.

•After attaching the control panel cover, check that the lock is fastened securely.

B Exhaust Vent

Warm air is expelled through this vent to keep the system cool. Do not block the exhaust vents as this may cause the unit to overheat and fail.

C AC Power Input Socket

This is the AC power input socket. Connect the supplied power cable to this socket.

D Remote Sensor (Rear)

When operating with the remote control, aim it towards the sensor. (Page 14)

•A remote sensor is also located at the front of the unit.

F Service Connector

This connector is intended for servicing pur- poses and should not normally be used.

G RS-232C Serial Port (D-sub 9 Pin) The projector can be controlled by serial com- mands from a computer or home automation control system connected to this port.

•For details, please check with your authorized dealer.

H DVI input (DVI-D 24 Pin)

This is the input socket for video signals. 1080/50p and 1080/60p signals are supported and HDCP content protection capability is provided.

10

Image 10

Contents ILA 1080MF1 For Customer use FCC Information U.S.A. only Safety precautionsMachine Noise Information Germany only Product If in DOUBT, Consult a Competent Electrician European Union Maintenance ProceduresInformation for Users on Disposal of Old Equipment EU Only Other Countries outside the European UnionPage Contents Accessories Controls & Features Rear & Right Side AC Power Input SocketService Connector Handling the Control Panel CoverMenu Button Rx/Tx IndicatorsControl Panel Exit ButtonOperate Indicator IndicatorsStandby Indicator Temp IndicatorControl panel indicators Indicator Display TableTop panel indicators Lamp replacementOn Button Remote ControlProjector/Processor Select buttons OFF ButtonLight Button Test Button main labelZoom Tele/Wide Buttons main labels 8 Installing the Projector View from the side Projector and Screen InstallationView from Above Screen Size and Projection Distance Wide T TeleRe-fit the lens shift cover Lens Shift SettingAdjust the projection screen position Projection screen position image according to shift levelConnecting a computer or Home Automation System via RS232 Connecting to DevicesConnecting a Video Processor Interfacing the ProjectorConnecting the Power Cable Supplied Apply Mains Power Adjusting zoom image size and focusTurning off the power Precautions During UseAdjustments and Settings Using Menus Menu StructureAfter setting is completed, press the Exit button Accessing the Menus Press the Menu buttonMenu Operation Buttons Color Temp Pixel AdjustSetup Menu Menu Position Red, Green, BlueSleep Time Power SaveOptions Menu Menu Display RC232C bpsAbout Lamp Replacement When the lamp usage time reaches 2010 hoursReplacing the Lamp Loosen the screws on the lamp unit and lift up the handle Lamp Replacement Procedure Remove the control panel coverLoosen the screw and remove the lamp cover Pull out the lamp unitTighten the screws of the lamp unit and fold down the handle Re-attach the lamp cover and fasten the screwCleaning and Replacing the Filter On-screen warning messages About warning indicators For NosTroubleshooting Power upPinouts RS-232C Port Interface SocketsDVI-D Interface RS-232C External Control Numeric value External control command tableSpecial parameters Specifications Projector Dimensions All dimensions in millimetres