Runco PL-61CX manual How to Attach Options to the Plasma Monitor

Page 11

How to Attach Options to the Plasma Monitor

You can attach your optional mounts or stand to the plasma monitor in one of the following two ways:

1)While it is upright. (See drawing A)

2)As it is laid down with the screen face down (See drawing B). Lay the protective sheet, which was wrapped around the plasma monitor when it was packaged, beneath the screen surface so it does not scratch the screen face.

*DO NOT touch or hold the screen face when carrying the unit.

Drawing A

•This device cannot be installed on its own. Be sure to use a stand or original mounting unit. (Wall mount unit, stand, etc.)

•For correct installation and mounting it is required to use a trained, RuncoAuthorized Dealer. Failure to follow correct mounting procedures could result in damage to the equipment or injury to the installer. Product warranty does not cover damage caused by improper installation.

Use only the mounting kit or stand provided by maufacturer and listed under options.

Ventilation Requirements for enclosure mounting

To allow heat to dispearse, leave space between surrounding objects as shown on the diagram to the right when installing.

	Wall
50mm (2")	50mm (2")
	50mm (2")

Drawing B

How to use the safety metal fittings and the screws for safety metal fittings

These are fittings for fastening the unit to a wall to prevent tipping due to external shock when using the stand (optional). Fasten the safety fittings to the holes in the back of the monitor using the safety fitting mount screws.

Wall* Safety metal fittings will differ according to the model.

Screw hole

Screw or Hook etc.

(Not supplied)

50mm (2")

50mm (2")

Safty metal fittings

Screw for Safety metal fittings

Metal chain (Not supplied)

Wall

Table Top

1

Image 11

Contents PL-61cx Table of Contents External Control Options Features you’ll enjoy includeContents of the package IntroductionRisk of Electric Shock Do not Open PrecautionsImportant Information Recommendations to avoid or minimize phosphor burn-in Plasma monitor cleaning procedureTo avoid damage and prolong operating life Three Year Limited Warranty RIGHTS, Limits and Exclusions TWO Year Limited Warranty RIGHTS, Limits and Exclusions How to Attach Options to the Plasma Monitor Part Names and Function Turns the plasma monitor’s power on and offReceives the signals from the remote control Sets the On-Screen Menu mode and displays the main menuConnect DVD’s, High Definition or Laser Discs, etc here Connect the included power cord hereRear View / Terminal Board Installation Remote Control Use of Installation Remote Control Battery Installation and Replacement 1/8 Stereo Mini cable must be purchased separeately Using the wired remote control modeOperating Range Video Plasma Monitor InstallationConnections with Equipment that have a Digital Interface Connecting Your Document CameraConnecting Your VCR or Laser Disc Player Connecting Your DVD PlayerPin No Signal Analog Pin Assignments and Signal Levels for 15 pin RGB AnalogCable Management Creating a video wallPFP Controller Installation & Overall Description Front Panel PFP Controller DescriptionRGB Output Video Inputs Rear PanelPFP Controller Remote Description Connection Examples Quick Set-up GuideMain Menu Menu TreePicture Quality Adjustments Page Page Side Bar Level Installation MenuInvert IR Code Select Output ShiftInput Shift Blanking System ResetBlanking Basic Operations To check the remaining time To set the off timerTo cancel the off timer After the power is turned off with the off timerWide Operations When viewing videos or digital video discs Picture Size setting Wide Screen Operation with Computer SignalsWhen Picture Size is set to OFF Supported resolutionMenu Operations Advanced menu modeMenu Tree ResetOPTION2 PWR. MGT Adjusting the picture Picture Settings MenuReducing noise in the picture Setting the color temperatureAdjusting the color to the desired level LOW Tone settings Making the Low Tone adjustments Adjusting the white balance Gamma settings Audio settings menu Audio Settings MenuAdjusting the colors Color Tune settingsExample Setting Audio INPUT1 to Video Image Adjust Settings MenuSetting the allocation of the audio connectors Adjusting the Position, Size, Fine Picture, Picture AdjSetting the on-screen menu Option1 Settings Menu OSM Orbiter settings Setting the BNC connectorsChecking the signal being transmitted to RGB1 terminal Setting a computer image to the correct RGB select screen RGB Select modes Setting high definition images to the suitable screen sizeSetting the Input Skip Input Skip settingsSetting the power management for computer images Option2 Settings MenuResetting to the default values Reducing burn-in of the screen POWER/STANDBY indicatorSetting the picture to suit the movie PLE settings Inverse Settings Orbiter settings Orbiter Function settings Screen Wiper Setting the time To select on for the Working Time Gray Level settings Setting the screen size for S1/S2 video input Soft Focus settings Setting the gray level for the sides of the screen PLUG/PLAY settings Setting the picture size for RGB input signalsSetting the signal and black level for DVI signal S1/S2 settingsPresent Time Option3 Settings MenuUsing the timer Present Time settings Special characters in the Program Timer screen Setting the power on mode To reset the program To reset the data IR Remote settings Enabling/disabling remote control wireless transmission PWR. on Mode settings Control Lock settingsID number setting Loop Out settingScreens Video Wall setting Divider settings Video Wall Position settings Image Adjust settings Auto ID settings DISP. Mode settings PLE Link On Delay Power on delay P. on Delay settings PLE Link settings Repeat Timer settings Advanced OSM Settings MenuSetting the menu mode Repeat TimerSetting the video signal format Language Settings MenuColor System Settings Menu Setting the language for the menusCommunication Parameters External ControlApplication ConnectionsComputer input signals supported by this system Table of Signals SupportedSupported resolution General Information PFP Controller RS-232 CommunicationsParameter min/max Value stored? PFP Controller RS-232 CommandsStore YES Symptom Checks Remedy TroubleshootingPage Plasma does not turn on After initial installation.Power LED on the front Yellow after the power buttonDefinition in the bright On, and the power LED onImage appears too Bright, and there is a loss169 Weight 140 lbs .5 kg1366 x DiagonalPfptm Controller Specifications & Dimensions RUMA-006830-SPL