Runco PL-61CX manual Blanking, System Reset

Page 34

Blanking

The BLANKING function allows you to 'cut off' part of the image to fit the screen properly, or to eliminate anomalies on the extreme outsides (usually the top) of the image. This can be done to the top, bottom, left or right sides individual- ly.

Blanking
Top	131
Bottom	707
Left	241
Right	1292

To adjust BLANKING, highlight the desired area you wish to blank (top, bottom, left or right), and use the left and right arrows to make the adjustment.

System Reset

In the event that your PL-61cxappears to have a software problem, or adjustments have been made so far out of range that the image is no longer on-screen or discernable, you can reset the processor back to factory values. This sets ALL settings back to factory values, so any adjustments made previously will be lost.

To reset your PL-61cx, follow this procedure:

·Turn off the MAIN POWER switch on the back of the processor

·Hold down the DOWN ARROW button, and turn the MAIN POWER SWITCH back on.Continue holding the down arrow button until the LED on the front panel blinks, then release the down arrow button.

Once this is done, your processor has been completely reset to factory values. After resetting the unit, Composite video will be the active source.

SYSTEM RESET is not on any of the menus; it must be performed using the instructions above.

24

Image 34

Contents PL-61cx Table of Contents External Control Introduction Features you’ll enjoy includeContents of the package OptionsImportant Information PrecautionsRisk of Electric Shock Do not Open To avoid damage and prolong operating life Plasma monitor cleaning procedureRecommendations to avoid or minimize phosphor burn-in Three Year Limited Warranty RIGHTS, Limits and Exclusions TWO Year Limited Warranty RIGHTS, Limits and Exclusions How to Attach Options to the Plasma Monitor Sets the On-Screen Menu mode and displays the main menu Turns the plasma monitor’s power on and offReceives the signals from the remote control Part Names and FunctionRear View / Terminal Board Connect the included power cord hereConnect DVD’s, High Definition or Laser Discs, etc here Installation Remote Control Use of Installation Remote Control Battery Installation and Replacement Operating Range Using the wired remote control mode1/8 Stereo Mini cable must be purchased separeately Plasma Monitor Installation VideoConnecting Your DVD Player Connecting Your Document CameraConnecting Your VCR or Laser Disc Player Connections with Equipment that have a Digital InterfacePin Assignments and Signal Levels for 15 pin RGB Analog Pin No Signal AnalogCreating a video wall Cable ManagementPFP Controller Installation & Overall Description PFP Controller Description Front PanelRear Panel RGB Output Video InputsPFP Controller Remote Description Quick Set-up Guide Connection ExamplesMenu Tree Main MenuPicture Quality Adjustments Page Page Installation Menu Side Bar LevelInvert Input Shift Output ShiftIR Code Select Blanking System ResetBlanking Basic Operations After the power is turned off with the off timer To set the off timerTo cancel the off timer To check the remaining timeWhen viewing videos or digital video discs Wide Operations Supported resolution Wide Screen Operation with Computer SignalsWhen Picture Size is set to OFF Picture Size setting Advanced menu mode Menu OperationsReset Menu TreeOPTION2 PWR. MGT Picture Settings Menu Adjusting the pictureAdjusting the color to the desired level Setting the color temperatureReducing noise in the picture Gamma settings Making the Low Tone adjustments Adjusting the white balance LOW Tone settings Color Tune settings Audio Settings MenuAdjusting the colors Audio settings menuAdjusting the Position, Size, Fine Picture, Picture Adj Image Adjust Settings MenuSetting the allocation of the audio connectors Example Setting Audio INPUT1 to VideoOption1 Settings Menu Setting the on-screen menuSetting a computer image to the correct RGB select screen Setting the BNC connectorsChecking the signal being transmitted to RGB1 terminal OSM Orbiter settings Input Skip settings Setting high definition images to the suitable screen sizeSetting the Input Skip RGB Select modesResetting to the default values Option2 Settings MenuSetting the power management for computer images PLE settings POWER/STANDBY indicatorSetting the picture to suit the movie Reducing burn-in of the screen Orbiter Function settings Orbiter settings Inverse Settings To select on for the Working Time Setting the timeScreen Wiper Setting the gray level for the sides of the screen Setting the screen size for S1/S2 video input Soft Focus settings Gray Level settings S1/S2 settings Setting the picture size for RGB input signalsSetting the signal and black level for DVI signal PLUG/PLAY settings Present Time settings Option3 Settings MenuUsing the timer Present Time To reset the data Setting the power on mode To reset the program Special characters in the Program Timer screen Control Lock settings Enabling/disabling remote control wireless transmission PWR. on Mode settings IR Remote settingsLoop Out setting ID number setting Video Wall Position settings Video Wall setting Divider settings Screens DISP. Mode settings Auto ID settings Image Adjust settings PLE Link settings On Delay Power on delay P. on Delay settings PLE LinkRepeat Timer Advanced OSM Settings MenuSetting the menu mode Repeat Timer settingsSetting the language for the menus Language Settings MenuColor System Settings Menu Setting the video signal formatConnections External ControlApplication Communication ParametersSupported resolution Table of Signals SupportedComputer input signals supported by this system PFP Controller RS-232 Communications General InformationPFP Controller RS-232 Commands Parameter min/max Value stored?Store YES Troubleshooting Symptom Checks RemedyPage Yellow after the power button After initial installation.Power LED on the front Plasma does not turn onBright, and there is a loss On, and the power LED onImage appears too Definition in the brightDiagonal Weight 140 lbs .5 kg1366 x 169Pfptm Controller Specifications & Dimensions RUMA-006830-SPL