Runco PL-61CX manual Basic Operations

Page 35

Basic Operations

POWER

To turn the unit ON and OFF:

1.Plug the power cord into an active AC power outlet.

2.Press the Power button (on the unit).

The monitor’s POWER/STANDBY indicator turns red and the standby mode is set.

3.Press the POWER ON button (on the remote control) to turn on the unit.

The monitor’s POWER/STANDBY indicator will light up (green) when the unit is on.

4.Press the POWER STANDBY button (on the remote control) or the Power button (on the unit) to turn off the unit.

The monitor’s POWER/STANDBY indicator turns red and the standby mode is set (only when turning off the unit with the remote control).

VOLUME

To adjust the sound volume:

1.Press and hold the VOLUME button (on the remote control or the unit) to increase to the desired level.

2.Press and hold the VOLUMEbutton (on the remote control or the unit) to decrease to the desired level.

MUTE

To cancel the sound:

Press the MUTE button on the remote control to cancel the sound; press again to restore.

DISPLAY

To check the settings:

1.The screen changes each time the DISPLAY button is pressed.

2.If the button is not pressed for approximately three seconds, the menu turns off.

DIGITAL ZOOM

Digital zoom specifies the picture position and enlarges the picture.

1.Press the POINTER button to display the pointer. ()

To change the size of the picture:

Press the ZOOM+ button and enlarge the picture.

The pointer will change to resemble a magnifying

glass. ( )

A press of the ZOOM- button will reduce the picture and return it to its original size.

To change the picture position:

Select the position with the ▲▼   buttons.

2.Press the POINTER button to delete the pointer.

AUTO ADJUST

To adjust the size or quality of the picture automatically:

Press the AUTO ADJUST button.

Information

AUTO ADJUST ON setting

When RGB (still picture) input

is selected ...... Fine Picture, Picture ADJ, Position,

and Contrast will be adjusted automatically.

When RGB (motion picture),

VIDEO, or Y/Pb/Pr (component) input

is selected ...... The screen size switches to ZOOM

mode automatically with the superimposed caption displayed fully only when the picture contains dark areas above and below the picture.

25

Image 35
Contents PL-61cx Table of Contents External Control Options Features you’ll enjoy includeContents of the package IntroductionRisk of Electric Shock Do not Open PrecautionsImportant Information Recommendations to avoid or minimize phosphor burn-in Plasma monitor cleaning procedureTo avoid damage and prolong operating life Three Year Limited Warranty RIGHTS, Limits and Exclusions TWO Year Limited Warranty RIGHTS, Limits and Exclusions How to Attach Options to the Plasma Monitor Part Names and Function Turns the plasma monitor’s power on and offReceives the signals from the remote control Sets the On-Screen Menu mode and displays the main menuConnect DVD’s, High Definition or Laser Discs, etc here Connect the included power cord hereRear View / Terminal Board Installation Remote Control Use of Installation Remote Control Battery Installation and Replacement 1/8 Stereo Mini cable must be purchased separeately Using the wired remote control modeOperating Range Video Plasma Monitor InstallationConnections with Equipment that have a Digital Interface Connecting Your Document CameraConnecting Your VCR or Laser Disc Player Connecting Your DVD PlayerPin No Signal Analog Pin Assignments and Signal Levels for 15 pin RGB AnalogCable Management Creating a video wallPFP Controller Installation & Overall Description Front Panel PFP Controller DescriptionRGB Output Video Inputs Rear PanelPFP Controller Remote Description Connection Examples Quick Set-up GuideMain Menu Menu TreePicture Quality Adjustments Page Page Side Bar Level Installation MenuInvert IR Code Select Output ShiftInput Shift Blanking System ResetBlanking Basic Operations To check the remaining time To set the off timerTo cancel the off timer After the power is turned off with the off timerWide Operations When viewing videos or digital video discs Picture Size setting Wide Screen Operation with Computer SignalsWhen Picture Size is set to OFF  Supported resolutionMenu Operations  Advanced menu modeMenu Tree ResetOPTION2 PWR. MGT Adjusting the picture Picture Settings MenuReducing noise in the picture Setting the color temperatureAdjusting the color to the desired level  LOW Tone settings Making the Low Tone adjustments Adjusting the white balance  Gamma settings Audio settings menu Audio Settings MenuAdjusting the colors  Color Tune settingsExample Setting Audio INPUT1 to Video Image Adjust Settings MenuSetting the allocation of the audio connectors Adjusting the Position, Size, Fine Picture, Picture AdjSetting the on-screen menu Option1 Settings Menu OSM Orbiter settings Setting the BNC connectorsChecking the signal being transmitted to RGB1 terminal Setting a computer image to the correct RGB select screen RGB Select modes Setting high definition images to the suitable screen sizeSetting the Input Skip  Input Skip settingsSetting the power management for computer images Option2 Settings MenuResetting to the default values Reducing burn-in of the screen POWER/STANDBY indicatorSetting the picture to suit the movie  PLE settings Inverse Settings  Orbiter settings Orbiter Function settings Screen Wiper  Setting the time To select on for the Working Time  Gray Level settings Setting the screen size for S1/S2 video input Soft Focus settings Setting the gray level for the sides of the screen PLUG/PLAY settings Setting the picture size for RGB input signalsSetting the signal and black level for DVI signal  S1/S2 settingsPresent Time Option3 Settings MenuUsing the timer  Present Time settings Special characters in the Program Timer screen Setting the power on mode To reset the program  To reset the data IR Remote settings Enabling/disabling remote control wireless transmission PWR. on Mode settings  Control Lock settingsID number setting Loop Out settingScreens Video Wall setting Divider settings  Video Wall Position settings Image Adjust settings  Auto ID settings DISP. Mode settings PLE Link On Delay Power on delay P. on Delay settings  PLE Link settings Repeat Timer settings Advanced OSM Settings MenuSetting the menu mode Repeat TimerSetting the video signal format Language Settings MenuColor System Settings Menu Setting the language for the menusCommunication Parameters External ControlApplication ConnectionsComputer input signals supported by this system Table of Signals SupportedSupported resolution General Information PFP Controller RS-232 CommunicationsParameter min/max Value stored? PFP Controller RS-232 CommandsStore YES Symptom Checks Remedy TroubleshootingPage Plasma does not turn on After initial installation.Power LED on the front Yellow after the power buttonDefinition in the bright On, and the power LED onImage appears too Bright, and there is a loss169 Weight 140 lbs .5 kg1366 x DiagonalPfptm Controller Specifications & Dimensions RUMA-006830-SPL