Runco PL-61CX manual Creating a video wall, Cable Management

Page 21

Creating a video wall

With buit-in matrix display capability, you can create a 2⋅ 2 or 3⋅ 3 video wall.

• Connect signal cables and remote cables as shown below.

Video signal		RGB/DVD/HD signal

BNC connector

				(	VIDEO	BNC connector	OUT
				VIDEO1 I N / OUT)			OUT
				VIDEO1 I N / OUT)			VIDEO Signal	RGB signal/	IN
		VIDEO 3			VIDEO 2		VIDEO Signal		IN
	RCA phono plug
IN	RCA phono plug							DVD/HD signal
IN								DVD/HD signal
VIDEO Signal		(		1AUDIO R
		)	L	1AUDIO R
		MONO
				Y
					DVD1

Remote	IN	I N
control	REMOTE	OUT	OUT	control
control			OUT	Remote
				Remote

Remote IN control

Cr/Pr	R/
G/ Y		RGB
Cb/Pb	B/	2 / DVD2
HD		/ HD2
VD
( IN / OUT		RGB 1
)
I N
REMOTE
OUT

OUT

OUT

RGB signal/ DVD/HD signal

Remote control

Note:

1. The VIDEO1 and RGB1 terminals can be used for either INPUT or OUTPUT.

When LOOP OUT is ON, do not connect an OUTPUT signal from another unit, that will place an extraordinary load on the other unit and may damage it.

2.LOOP OUT can not be turned ON while signals are input to RGB1 terminal.

3.LOOP OUT can be turned ON while signals are input to RGB1 terminal if the POWER is switched ON.

Information

•To loop signals out to another plasma display, set the LOOP OUT to ON.

•To create a video wall, set the VIDEO WALL menu items properly.

•To connect monitors, please use a 1~2m (3.3~6.6 feet) BNC cable (any commercially available cable).

•If the image quality is poor, do not use the monitor’s out terminal. Use a distribution amplifier (any commercially available distribution amplifier) to connect the split signals to the respective monitor INPUT terminals.

•Being used as a video wall function, maximaly 4-screen is rough-standard with lower than 1024768, 60Hz signal.

•A distribution amplifier is particularly recommended when using a 9-screen video wall.

•From the second monitor onward, connections require a BNC-RCA conversion cable or connector, a mini D-Sub 15 pin cable-BNC (5) cable or a conversion connector.

Cable Management

Using the cable clamps provided with the plasma display, bundle at the back of the unit the signal and audio cables connected to the display.

* The cable clamp will differ according to the model.

Back of the unit

mounting hooks/mounting holes

To attach

1.	2.
	clamp
mounting hook	cables
To attach
1.	2.
	clamp

To detach

To detach

mounting hole

cables

11

Image 21

Contents PL-61cx Table of Contents External Control Contents of the package Features you’ll enjoy includeIntroduction OptionsPrecautions Important InformationRisk of Electric Shock Do not Open Plasma monitor cleaning procedure To avoid damage and prolong operating lifeRecommendations to avoid or minimize phosphor burn-in Three Year Limited Warranty RIGHTS, Limits and Exclusions TWO Year Limited Warranty RIGHTS, Limits and Exclusions How to Attach Options to the Plasma Monitor Receives the signals from the remote control Turns the plasma monitor’s power on and offSets the On-Screen Menu mode and displays the main menu Part Names and FunctionConnect the included power cord here Rear View / Terminal BoardConnect DVD’s, High Definition or Laser Discs, etc here Installation Remote Control Use of Installation Remote Control Battery Installation and Replacement Using the wired remote control mode Operating Range1/8 Stereo Mini cable must be purchased separeately Video Plasma Monitor InstallationConnecting Your VCR or Laser Disc Player Connecting Your Document CameraConnecting Your DVD Player Connections with Equipment that have a Digital InterfacePin No Signal Analog Pin Assignments and Signal Levels for 15 pin RGB AnalogCable Management Creating a video wallPFP Controller Installation & Overall Description Front Panel PFP Controller DescriptionRGB Output Video Inputs Rear PanelPFP Controller Remote Description Connection Examples Quick Set-up GuideMain Menu Menu TreePicture Quality Adjustments Page Page Side Bar Level Installation MenuInvert Output Shift Input ShiftIR Code Select System Reset BlankingBlanking Basic Operations To cancel the off timer To set the off timerAfter the power is turned off with the off timer To check the remaining timeWide Operations When viewing videos or digital video discsWhen Picture Size is set to OFF Wide Screen Operation with Computer Signals Supported resolution Picture Size settingMenu Operations Advanced menu modeMenu Tree ResetOPTION2 PWR. MGT Adjusting the picture Picture Settings MenuSetting the color temperature Adjusting the color to the desired levelReducing noise in the picture Adjusting the white balance Making the Low Tone adjustments Gamma settings LOW Tone settingsAdjusting the colors Audio Settings Menu Color Tune settings Audio settings menuSetting the allocation of the audio connectors Image Adjust Settings MenuAdjusting the Position, Size, Fine Picture, Picture Adj Example Setting Audio INPUT1 to VideoSetting the on-screen menu Option1 Settings MenuChecking the signal being transmitted to RGB1 terminal Setting the BNC connectorsSetting a computer image to the correct RGB select screen OSM Orbiter settingsSetting the Input Skip Setting high definition images to the suitable screen size Input Skip settings RGB Select modesOption2 Settings Menu Resetting to the default valuesSetting the power management for computer images Setting the picture to suit the movie POWER/STANDBY indicator PLE settings Reducing burn-in of the screen Orbiter settings Orbiter Function settings Inverse Settings Setting the time To select on for the Working TimeScreen Wiper Soft Focus settings Setting the screen size for S1/S2 video inputSetting the gray level for the sides of the screen Gray Level settingsSetting the signal and black level for DVI signal Setting the picture size for RGB input signals S1/S2 settings PLUG/PLAY settingsUsing the timer Option3 Settings Menu Present Time settings Present Time To reset the program Setting the power on mode To reset the data Special characters in the Program Timer screen PWR. on Mode settings Enabling/disabling remote control wireless transmission Control Lock settings IR Remote settingsID number setting Loop Out setting Divider settings Video Wall setting Video Wall Position settings Screens Auto ID settings DISP. Mode settings Image Adjust settings P. on Delay settings On Delay Power on delay PLE Link settings PLE LinkSetting the menu mode Advanced OSM Settings MenuRepeat Timer Repeat Timer settingsColor System Settings Menu Language Settings MenuSetting the language for the menus Setting the video signal formatApplication External ControlConnections Communication ParametersTable of Signals Supported Supported resolutionComputer input signals supported by this system General Information PFP Controller RS-232 CommunicationsParameter min/max Value stored? PFP Controller RS-232 CommandsStore YES Symptom Checks Remedy TroubleshootingPage Power LED on the front After initial installation.Yellow after the power button Plasma does not turn onImage appears too On, and the power LED onBright, and there is a loss Definition in the bright1366 x Weight 140 lbs .5 kgDiagonal 169Pfptm Controller Specifications & Dimensions RUMA-006830-SPL