Runco PL-61CX manual Installation Menu, Side Bar Level

Page 31

Installation Menu

The Installation menu is where you can adjust the image orientation, adjust keystone and even check the age of the lamp in the Plasma.

When the Controller is turned on for the first time, the INSTALLATION item will not appear in the main menu. To enable the INSTALLATION menu, there are two options:

·With the processor ON and no menus on-screen, simultaneously press the ENTER, UP and LEFT buttons (you don't need to hold them down). Release the three buttons and press MENU, ensure INSTALLER ADJUST is now on the bottom of the main menu.

·With the remote control, press button 6 (with no menus on-screen). After pressing '6', press MENU and ensure INSTALLER ADJUST is now on the bottom of the main menu.

After INSTALLER MODE has been accessed, press MENU, highlight INSTALLER ADJUST and press ENTER. This will bring up the INSTALLATION MENU, shown here:

Once the installation mode has been enabled, you will also be able to access Luma Enhance, Chroma Enhance and Color Balance. These items will not appear anywhere in the menu until the installation mode is enabled.

INSTALLATION

Side Bar Level

InvertOff

Output Shift

Input Shift

Blanking

IR Code Select

Side Bar Level

Phosphor-based displays such as Plasma (flat panel) displays, can be 'burned' by still-images or otherwise not using the full display or raster. Examples of this include ATM's, where the bank logo is permanently burned into the display. This is also the reason why most Plasma manufacturers strongly recommend against the use of video games with projection televisions, as many video games have still images in them.

Besides still images, using a 4:3 image on a widescreen display could cause a '4:3 burn' (see below):

Side

Bar

Area

Side

Bar

Area

Widescreen display

‘4:3 burn’

21

Image 31

Contents PL-61cx Table of Contents External Control Options Features you’ll enjoy includeContents of the package IntroductionImportant Information PrecautionsRisk of Electric Shock Do not Open To avoid damage and prolong operating life Plasma monitor cleaning procedureRecommendations to avoid or minimize phosphor burn-in Three Year Limited Warranty RIGHTS, Limits and Exclusions TWO Year Limited Warranty RIGHTS, Limits and Exclusions How to Attach Options to the Plasma Monitor Part Names and Function Turns the plasma monitor’s power on and offReceives the signals from the remote control Sets the On-Screen Menu mode and displays the main menuRear View / Terminal Board Connect the included power cord hereConnect DVD’s, High Definition or Laser Discs, etc here Installation Remote Control Use of Installation Remote Control Battery Installation and Replacement Operating Range Using the wired remote control mode1/8 Stereo Mini cable must be purchased separeately Video Plasma Monitor InstallationConnections with Equipment that have a Digital Interface Connecting Your Document CameraConnecting Your VCR or Laser Disc Player Connecting Your DVD PlayerPin No Signal Analog Pin Assignments and Signal Levels for 15 pin RGB AnalogCable Management Creating a video wallPFP Controller Installation & Overall Description Front Panel PFP Controller DescriptionRGB Output Video Inputs Rear PanelPFP Controller Remote Description Connection Examples Quick Set-up GuideMain Menu Menu TreePicture Quality Adjustments Page Page Side Bar Level Installation MenuInvert Input Shift Output ShiftIR Code Select Blanking System ResetBlanking Basic Operations To check the remaining time To set the off timerTo cancel the off timer After the power is turned off with the off timerWide Operations When viewing videos or digital video discs Picture Size setting Wide Screen Operation with Computer SignalsWhen Picture Size is set to OFF Supported resolutionMenu Operations Advanced menu modeMenu Tree ResetOPTION2 PWR. MGT Adjusting the picture Picture Settings MenuAdjusting the color to the desired level Setting the color temperatureReducing noise in the picture LOW Tone settings Making the Low Tone adjustments Adjusting the white balance Gamma settings Audio settings menu Audio Settings MenuAdjusting the colors Color Tune settingsExample Setting Audio INPUT1 to Video Image Adjust Settings MenuSetting the allocation of the audio connectors Adjusting the Position, Size, Fine Picture, Picture AdjSetting the on-screen menu Option1 Settings Menu OSM Orbiter settings Setting the BNC connectorsChecking the signal being transmitted to RGB1 terminal Setting a computer image to the correct RGB select screen RGB Select modes Setting high definition images to the suitable screen sizeSetting the Input Skip Input Skip settingsResetting to the default values Option2 Settings MenuSetting the power management for computer images Reducing burn-in of the screen POWER/STANDBY indicatorSetting the picture to suit the movie PLE settings Orbiter Function settings Orbiter settings Inverse Settings To select on for the Working Time Setting the timeScreen Wiper Gray Level settings Setting the screen size for S1/S2 video input Soft Focus settings Setting the gray level for the sides of the screen PLUG/PLAY settings Setting the picture size for RGB input signalsSetting the signal and black level for DVI signal S1/S2 settingsPresent Time Option3 Settings MenuUsing the timer Present Time settings Special characters in the Program Timer screen Setting the power on mode To reset the program To reset the data IR Remote settings Enabling/disabling remote control wireless transmission PWR. on Mode settings Control Lock settingsID number setting Loop Out settingScreens Video Wall setting Divider settings Video Wall Position settings DISP. Mode settings Auto ID settings Image Adjust settings PLE Link On Delay Power on delay P. on Delay settings PLE Link settings Repeat Timer settings Advanced OSM Settings MenuSetting the menu mode Repeat TimerSetting the video signal format Language Settings MenuColor System Settings Menu Setting the language for the menusCommunication Parameters External ControlApplication ConnectionsSupported resolution Table of Signals SupportedComputer input signals supported by this system General Information PFP Controller RS-232 CommunicationsParameter min/max Value stored? PFP Controller RS-232 CommandsStore YES Symptom Checks Remedy TroubleshootingPage Plasma does not turn on After initial installation.Power LED on the front Yellow after the power buttonDefinition in the bright On, and the power LED onImage appears too Bright, and there is a loss169 Weight 140 lbs .5 kg1366 x DiagonalPfptm Controller Specifications & Dimensions RUMA-006830-SPL