Runco PL-61CX manual Image appears too, Bright, and there is a loss, Definition in the bright

Page 73

The image appears too	· Contrast is set too high.	· Turn down the CONTRAST
bright, and there is a loss	· The DVD player is set for a	level on the Controller. Mid-
of definition in the bright-	high-level output.	range is -10; it is recom-
est areas of the image.	· The video signal has not	mended to keep it below 0 to
	been terminated properly	prevent this problem.
	somewhere in the system.	· Set the DVD player for a
		nominal output (no boost or
		gain).
		· Ensure all video signals are
		terminated in 75 Ohms.

The image appears too	· Brightness is set too high.	· Turn down the BRIGHT-
'washed out', or the dark-	· The DVD player may be set	NESS level on the Controller.
est areas of the image	for too high of a brightness	If possible, use a PLUGE
appear too bright.	level.	pattern to set the brightness
		level properly.
		· Set the DVD player for a
		nominal output (no boost or
		gain).

The colors of the image	· The Red, Green and/or	· Check the cable connec-
appear abnormal	Blue outputs of the Controller	tions on the back of the
	or inputs to the Plasma are	Controller or on the Plasma.
	reversed.
	· The Pr and Pb inputs on the
	Component input on the
	Controller are reversed

The Plasma will not turn	· The Controller may have	· Unplug the Controller for 2
on, and the power LED on	'locked-up'.	minutes; plug it back in and
the front of the Controller		re-try.
is blinking red or green.		· Perform a system reset on
		the Controller and then re-try.

63

Image 73

Contents PL-61cx Table of Contents External Control Contents of the package Features you’ll enjoy includeIntroduction OptionsImportant Information PrecautionsRisk of Electric Shock Do not Open To avoid damage and prolong operating life Plasma monitor cleaning procedureRecommendations to avoid or minimize phosphor burn-in Three Year Limited Warranty RIGHTS, Limits and Exclusions TWO Year Limited Warranty RIGHTS, Limits and Exclusions How to Attach Options to the Plasma Monitor Receives the signals from the remote control Turns the plasma monitor’s power on and offSets the On-Screen Menu mode and displays the main menu Part Names and FunctionRear View / Terminal Board Connect the included power cord hereConnect DVD’s, High Definition or Laser Discs, etc here Installation Remote Control Use of Installation Remote Control Battery Installation and Replacement Operating Range Using the wired remote control mode1/8 Stereo Mini cable must be purchased separeately Video Plasma Monitor InstallationConnecting Your VCR or Laser Disc Player Connecting Your Document CameraConnecting Your DVD Player Connections with Equipment that have a Digital InterfacePin No Signal Analog Pin Assignments and Signal Levels for 15 pin RGB AnalogCable Management Creating a video wallPFP Controller Installation & Overall Description Front Panel PFP Controller DescriptionRGB Output Video Inputs Rear PanelPFP Controller Remote Description Connection Examples Quick Set-up GuideMain Menu Menu TreePicture Quality Adjustments Page Page Side Bar Level Installation MenuInvert Input Shift Output ShiftIR Code Select Blanking System ResetBlanking Basic Operations To cancel the off timer To set the off timerAfter the power is turned off with the off timer To check the remaining timeWide Operations When viewing videos or digital video discsWhen Picture Size is set to OFF Wide Screen Operation with Computer Signals Supported resolution Picture Size settingMenu Operations Advanced menu modeMenu Tree ResetOPTION2 PWR. MGT Adjusting the picture Picture Settings MenuAdjusting the color to the desired level Setting the color temperatureReducing noise in the picture Adjusting the white balance Making the Low Tone adjustments Gamma settings LOW Tone settingsAdjusting the colors Audio Settings Menu Color Tune settings Audio settings menuSetting the allocation of the audio connectors Image Adjust Settings MenuAdjusting the Position, Size, Fine Picture, Picture Adj Example Setting Audio INPUT1 to VideoSetting the on-screen menu Option1 Settings MenuChecking the signal being transmitted to RGB1 terminal Setting the BNC connectorsSetting a computer image to the correct RGB select screen OSM Orbiter settingsSetting the Input Skip Setting high definition images to the suitable screen size Input Skip settings RGB Select modesResetting to the default values Option2 Settings MenuSetting the power management for computer images Setting the picture to suit the movie POWER/STANDBY indicator PLE settings Reducing burn-in of the screen Orbiter Function settings Orbiter settings Inverse Settings To select on for the Working Time Setting the timeScreen Wiper Soft Focus settings Setting the screen size for S1/S2 video inputSetting the gray level for the sides of the screen Gray Level settingsSetting the signal and black level for DVI signal Setting the picture size for RGB input signals S1/S2 settings PLUG/PLAY settingsUsing the timer Option3 Settings Menu Present Time settings Present Time To reset the program Setting the power on mode To reset the data Special characters in the Program Timer screen PWR. on Mode settings Enabling/disabling remote control wireless transmission Control Lock settings IR Remote settingsID number setting Loop Out setting Divider settings Video Wall setting Video Wall Position settings Screens DISP. Mode settings Auto ID settings Image Adjust settings P. on Delay settings On Delay Power on delay PLE Link settings PLE LinkSetting the menu mode Advanced OSM Settings MenuRepeat Timer Repeat Timer settingsColor System Settings Menu Language Settings MenuSetting the language for the menus Setting the video signal formatApplication External ControlConnections Communication ParametersSupported resolution Table of Signals SupportedComputer input signals supported by this system General Information PFP Controller RS-232 CommunicationsParameter min/max Value stored? PFP Controller RS-232 CommandsStore YES Symptom Checks Remedy TroubleshootingPage Power LED on the front After initial installation.Yellow after the power button Plasma does not turn onImage appears too On, and the power LED onBright, and there is a loss Definition in the bright1366 x Weight 140 lbs .5 kgDiagonal 169Pfptm Controller Specifications & Dimensions RUMA-006830-SPL