Runco PL-61CX manual Rear View / Terminal Board, Connect the included power cord here

Page 13

Rear View / Terminal Board

		(	VIDEO VIDEO 2
C		IN/OUT
C	VIDEO 3	1VIDEO )
	(	AUDIO 1 R
	MONO
	L )
		Y
E		Cb/Pb	DVD1 / HD
		Cr/Pr	1
	(	AUDIO 2 R
	MONO
	L )
		R/ Cr/Pr
F		G/ B/ Y Cb/Pb	RGB2 / DVD2 /
		HD	HD2
		VD
G		(IN / OUT)	RGB 1
	(	AUDIO 3 R
	MONO
	L )
H		DVI ( Digital	RGB 3
H		RGB
		)
I		External
I		Control
J		IN
J		REMOTE
		REMOTE
K		OUT
K

D

AC IN

AC IN

RIGHT	LEFT	SPEAKERS MUST
		HAVE MORE THAN
		7WATT RATING
		IMPEDANCE 6 OHM

AB

AAC IN

Connect the included power cord here.

BConnect speakers (optional) here. Maintain the correct polarity. Please refer to your speaker’s owner’s manual.

CVIDEO 1,2,3 (BNC, RCA, S-Video)

Connect VCR’s, DVD’s or VIdeo Cameras, etc here. VIDEO1 can be used for INPUT or OUTPUT.

DAUDIO1, AUDIO2, AUDIO3

These are audio input terminals. The input is selectable. Set which video image to distribute them from the audio menu screen.

EDVD1 / HD1

Connect DVD’s, High Definition or Laser Discs, etc here.

FRGB2 / DVD2 / HD2

RGB2: Connect an analog RGB signal and the synchronization signal.

DVD2 / HD2: Connect DVD’s, High Definition sources, Laser Discs, etc. here. This input can be set for use with an RGB or Component source.

GRGB1 (mini D-Sub 15pin)

Connect an analog RGB signal from a computer, etc. here. This input can be used for Input or Output.

HRGB3 (DVI 24pin)

Connect a digital signal (TMDS) from a source with a DVI output.

I EXTERNAL CONTROL

This terminal is used when operating and controlling the monitor externally by RS-232.

J REMOTE IN

Connect the remote cable* to the remote control’s remote jack to obtain wired remote control).

KREMOTE OUT

Connect the remote cable* to the REMOTE IN jack of the other display monitor to obtain wired remote control.

* The 1/8 Stereo Mini cable must be purchased separately.

3

Image 13

Contents PL-61cx Table of Contents External Control Contents of the package Features you’ll enjoy includeIntroduction OptionsImportant Information PrecautionsRisk of Electric Shock Do not Open To avoid damage and prolong operating life Plasma monitor cleaning procedureRecommendations to avoid or minimize phosphor burn-in Three Year Limited Warranty RIGHTS, Limits and Exclusions TWO Year Limited Warranty RIGHTS, Limits and Exclusions How to Attach Options to the Plasma Monitor Receives the signals from the remote control Turns the plasma monitor’s power on and offSets the On-Screen Menu mode and displays the main menu Part Names and FunctionRear View / Terminal Board Connect the included power cord hereConnect DVD’s, High Definition or Laser Discs, etc here Installation Remote Control Use of Installation Remote Control Battery Installation and Replacement Operating Range Using the wired remote control mode1/8 Stereo Mini cable must be purchased separeately Video Plasma Monitor InstallationConnecting Your VCR or Laser Disc Player Connecting Your Document CameraConnecting Your DVD Player Connections with Equipment that have a Digital InterfacePin No Signal Analog Pin Assignments and Signal Levels for 15 pin RGB AnalogCable Management Creating a video wallPFP Controller Installation & Overall Description Front Panel PFP Controller DescriptionRGB Output Video Inputs Rear PanelPFP Controller Remote Description Connection Examples Quick Set-up GuideMain Menu Menu TreePicture Quality Adjustments Page Page Side Bar Level Installation MenuInvert Input Shift Output ShiftIR Code Select Blanking System ResetBlanking Basic Operations To cancel the off timer To set the off timerAfter the power is turned off with the off timer To check the remaining timeWide Operations When viewing videos or digital video discsWhen Picture Size is set to OFF Wide Screen Operation with Computer Signals Supported resolution Picture Size settingMenu Operations Advanced menu modeMenu Tree ResetOPTION2 PWR. MGT Adjusting the picture Picture Settings MenuAdjusting the color to the desired level Setting the color temperatureReducing noise in the picture Adjusting the white balance Making the Low Tone adjustments Gamma settings LOW Tone settingsAdjusting the colors Audio Settings Menu Color Tune settings Audio settings menuSetting the allocation of the audio connectors Image Adjust Settings MenuAdjusting the Position, Size, Fine Picture, Picture Adj Example Setting Audio INPUT1 to VideoSetting the on-screen menu Option1 Settings MenuChecking the signal being transmitted to RGB1 terminal Setting the BNC connectorsSetting a computer image to the correct RGB select screen OSM Orbiter settingsSetting the Input Skip Setting high definition images to the suitable screen size Input Skip settings RGB Select modesResetting to the default values Option2 Settings MenuSetting the power management for computer images Setting the picture to suit the movie POWER/STANDBY indicator PLE settings Reducing burn-in of the screen Orbiter Function settings Orbiter settings Inverse Settings To select on for the Working Time Setting the timeScreen Wiper Soft Focus settings Setting the screen size for S1/S2 video inputSetting the gray level for the sides of the screen Gray Level settingsSetting the signal and black level for DVI signal Setting the picture size for RGB input signals S1/S2 settings PLUG/PLAY settingsUsing the timer Option3 Settings Menu Present Time settings Present Time To reset the program Setting the power on mode To reset the data Special characters in the Program Timer screen PWR. on Mode settings Enabling/disabling remote control wireless transmission Control Lock settings IR Remote settingsID number setting Loop Out setting Divider settings Video Wall setting Video Wall Position settings Screens DISP. Mode settings Auto ID settings Image Adjust settings P. on Delay settings On Delay Power on delay PLE Link settings PLE LinkSetting the menu mode Advanced OSM Settings MenuRepeat Timer Repeat Timer settingsColor System Settings Menu Language Settings MenuSetting the language for the menus Setting the video signal formatApplication External ControlConnections Communication ParametersSupported resolution Table of Signals SupportedComputer input signals supported by this system General Information PFP Controller RS-232 CommunicationsParameter min/max Value stored? PFP Controller RS-232 CommandsStore YES Symptom Checks Remedy TroubleshootingPage Power LED on the front After initial installation.Yellow after the power button Plasma does not turn onImage appears too On, and the power LED onBright, and there is a loss Definition in the bright1366 x Weight 140 lbs .5 kgDiagonal 169Pfptm Controller Specifications & Dimensions RUMA-006830-SPL