Runco PL-61CX manual RIGHTS, Limits and Exclusions

Page 8

CAUTION: THIS LIMITED WARRANTY ONLY COVERS RUNCO PRODUCTS PURCHASED FROM AND INSTALLED BY RUNCO AUTHORIZED DEALERS. ALL OTHER PRODUCTS ARE SPECIFICALLY EXCLUDED FROM COVERAGE UNDER THIS LIMITED WARRANTY. MOREOVER, DAMAGE RESULTING DIRECTLY OR INDIRECTLY FROM IMPROPER INSTALLATION OR SETUP IS SPECIFICALLY EXCLUDED FROM COVERAGE UNDER THIS LIMITED WARRANTY.

RIGHTS, LIMITS AND EXCLUSIONS:

Runco limits its obligations under any implied warranties under state laws to a period not to exceed the warranty period. There are no express warranties. Runco also excludes any obligation on its part for incidental or consequential damages related to the failure of this product to function properly. Some states do not allow limitations on how long an implied warranty lasts, and some states do not allow the exclusion or limitation of incidental or consequential damages. So the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights that vary from state to state.

EFFECTIVE WARRANTY DATE:

This warranty begins on the effective date of delivery to the end user. For your convenience, keep the original bill of sale as evidence of the purchase date.

IMPORTANT: WARRANTY REGISTRATION:

Please fill out and mail your warranty registration card. It is imperative that Runco knows how to reach you promptly if we should discover a safety problem or product update for which you must be notified.

CONTACT A RUNCO AUTHORIZED SERVICE CENTER TO OBTAIN SERVICE

Repairs made under the terms of this Limited Warranty covering your Runco video product will be performed at the location of the product, during usual working hours, providing location of product is within normal operating distance from a Runco Authorized Service Center. In some instances it may be necessary for the product to be returned to the Runco factory for repairs. If, solely in Runco’s judgment, location of product to be repaired is beyond normal operating distance of the closest Runco Authorized Service Center, or the repair requires the unit be returned to the Runco factory, it is the owner’s responsibility to arrange for shipment of the product for repair. These arrangements must be made through the selling Runco Dealer. If this is not possible, contact Runco directly and we will locate an authorized representative to assist in the return of your product to Runco. Runco will return product transportation prepaid in the United States, unless no product defect is discovered. In that instance, shipping costs will be the responsibility of the owner.

ADDITIONAL INFORMATION:

To locate the name and address of the nearest Runco Authorized Service Center, or for additional information about this Limited Warranty, please call or write:

RUNCO INTERNATIONAL

Attn: Customer Service Department

2900 Faber Street

Union City, CA 94587

Ph: (510) 324-7777

Fax: (510) 324-9300

Image 8
Contents PL-61cx Table of Contents External Control Features you’ll enjoy include Contents of the packageIntroduction OptionsRisk of Electric Shock Do not Open PrecautionsImportant Information Recommendations to avoid or minimize phosphor burn-in Plasma monitor cleaning procedureTo avoid damage and prolong operating life Three Year Limited Warranty RIGHTS, Limits and Exclusions TWO Year Limited Warranty RIGHTS, Limits and Exclusions How to Attach Options to the Plasma Monitor Turns the plasma monitor’s power on and off Receives the signals from the remote controlSets the On-Screen Menu mode and displays the main menu Part Names and FunctionConnect DVD’s, High Definition or Laser Discs, etc here Connect the included power cord hereRear View / Terminal Board Installation Remote Control Use of Installation Remote Control Battery Installation and Replacement 1/8 Stereo Mini cable must be purchased separeately Using the wired remote control modeOperating Range Plasma Monitor Installation VideoConnecting Your Document Camera Connecting Your VCR or Laser Disc PlayerConnecting Your DVD Player Connections with Equipment that have a Digital InterfacePin Assignments and Signal Levels for 15 pin RGB Analog Pin No Signal AnalogCreating a video wall Cable ManagementPFP Controller Installation & Overall Description PFP Controller Description Front PanelRear Panel RGB Output Video InputsPFP Controller Remote Description Quick Set-up Guide Connection ExamplesMenu Tree Main MenuPicture Quality Adjustments Page Page Installation Menu Side Bar LevelInvert IR Code Select Output ShiftInput Shift Blanking System ResetBlanking Basic Operations To set the off timer To cancel the off timerAfter the power is turned off with the off timer To check the remaining timeWhen viewing videos or digital video discs Wide OperationsWide Screen Operation with Computer Signals When Picture Size is set to OFF Supported resolution  Picture Size setting Advanced menu mode Menu OperationsReset Menu TreeOPTION2 PWR. MGT Picture Settings Menu Adjusting the pictureReducing noise in the picture Setting the color temperatureAdjusting the color to the desired level Making the Low Tone adjustments  Adjusting the white balance Gamma settings  LOW Tone settingsAudio Settings Menu Adjusting the colors Color Tune settings  Audio settings menuImage Adjust Settings Menu Setting the allocation of the audio connectorsAdjusting the Position, Size, Fine Picture, Picture Adj Example Setting Audio INPUT1 to VideoOption1 Settings Menu Setting the on-screen menuSetting the BNC connectors Checking the signal being transmitted to RGB1 terminalSetting a computer image to the correct RGB select screen  OSM Orbiter settingsSetting high definition images to the suitable screen size Setting the Input Skip Input Skip settings  RGB Select modesSetting the power management for computer images Option2 Settings MenuResetting to the default values POWER/STANDBY indicator Setting the picture to suit the movie PLE settings Reducing burn-in of the screen Inverse Settings  Orbiter settings Orbiter Function settings Screen Wiper  Setting the time To select on for the Working Time Setting the screen size for S1/S2 video input  Soft Focus settingsSetting the gray level for the sides of the screen  Gray Level settingsSetting the picture size for RGB input signals Setting the signal and black level for DVI signal S1/S2 settings  PLUG/PLAY settingsOption3 Settings Menu Using the timer Present Time settings Present TimeSetting the power on mode  To reset the program To reset the data  Special characters in the Program Timer screenEnabling/disabling remote control wireless transmission  PWR. on Mode settings Control Lock settings  IR Remote settingsLoop Out setting ID number settingVideo Wall setting  Divider settings Video Wall Position settings Screens Image Adjust settings  Auto ID settings DISP. Mode settings On Delay Power on delay  P. on Delay settings PLE Link settings PLE LinkAdvanced OSM Settings Menu Setting the menu modeRepeat Timer  Repeat Timer settingsLanguage Settings Menu Color System Settings MenuSetting the language for the menus Setting the video signal formatExternal Control ApplicationConnections Communication ParametersComputer input signals supported by this system Table of Signals SupportedSupported resolution PFP Controller RS-232 Communications General InformationPFP Controller RS-232 Commands Parameter min/max Value stored?Store YES Troubleshooting Symptom Checks RemedyPage After initial installation. Power LED on the frontYellow after the power button Plasma does not turn onOn, and the power LED on Image appears tooBright, and there is a loss Definition in the brightWeight 140 lbs .5 kg 1366 xDiagonal 169Pfptm Controller Specifications & Dimensions RUMA-006830-SPL