Runco PL-61CX manual Menu Operations, Advanced menu mode

Page 39

OSM(On Screen Menu) Controls

Menu Operations

The OSM window is displayed with respect to the screen as shown on the diagram.

*Depending on the screen’s mode, the OSM may be displayed differently.

In the explanation, the OSM section is shown close up.

		MAIN MENU			1 / 2
	PICTURE

	AUDIO
	IMAGE ADJUST
	OPTION1
	ADVANCED OSM			:	OFF
	NEXT PAGE
	SEL.	MENU/ENTER	OK		EXIT	EXIT

The following describes how to use the menus and the selected items.

1.Press the MENU/ENTER button on the remote control to display the MAIN MENU.

				MAIN MENU			1 / 2
	PICTURE

AUDIO
IMAGE ADJUST
OPTION1
ADVANCED OSM						:	OFF
		NEXT PAGE
		SEL.		MENU/ENTER	OK		EXIT	EXIT

				MAIN MENU			2 / 2
		PREVIOUS PAGE
	LANGUAGE
COLOR SYSTEM
SOURCE INFORMATION
		SEL.			OK			EXIT
				MENU/ENTER
				MENU/ENTER			EXIT

2. Press the cursor buttons ▲ ▼on the remote control to highlight the menu you wish to enter.

3.Press the MENU/ENTER button on the remote control to select a sub menu or item.

			PICTURE		1 / 2
	CONTRAST

	BRIGHTNESS
	SHARPNESS
	COLOR
	COLOR
	TINT
	PICTURE MODE			:	NORMAL
	NR			:	OFF
	NEXT PAGE
	SEL.		ADJ.		EXIT	RETURN

4.Adjust the level or change the setting of the selected item by using the cursor buttons on the remote control.

5.The adjustments or the settings that are stored in memory.

The change is stored until you change it again.

6.Repeat steps 2 – 5 to adjust an additional item, or press the EXIT button on the remote control to return to the main menu.

Note: The main menu disappears by pressing the EXIT button.

Information

Advanced menu mode

When “ADVANCED OSM” is set to “ON” in the main menu (1/2), full menu items will be shown.

	MAIN MENU	1 / 2
PICTURE
AUDIO
IMAGE ADJUST
OPTION1
OPTION2
OPTION3

	ADVANCED OSM			: ON
	NEXT PAGE
	SEL.		OK			EXIT
		MENU/ENTER
					EXIT

29

Image 39

Contents PL-61cx Table of Contents External Control Options Features you’ll enjoy includeContents of the package IntroductionPrecautions Important InformationRisk of Electric Shock Do not Open Plasma monitor cleaning procedure To avoid damage and prolong operating lifeRecommendations to avoid or minimize phosphor burn-in Three Year Limited Warranty RIGHTS, Limits and Exclusions TWO Year Limited Warranty RIGHTS, Limits and Exclusions How to Attach Options to the Plasma Monitor Part Names and Function Turns the plasma monitor’s power on and offReceives the signals from the remote control Sets the On-Screen Menu mode and displays the main menuConnect the included power cord here Rear View / Terminal BoardConnect DVD’s, High Definition or Laser Discs, etc here Installation Remote Control Use of Installation Remote Control Battery Installation and Replacement Using the wired remote control mode Operating Range1/8 Stereo Mini cable must be purchased separeately Video Plasma Monitor InstallationConnections with Equipment that have a Digital Interface Connecting Your Document CameraConnecting Your VCR or Laser Disc Player Connecting Your DVD PlayerPin No Signal Analog Pin Assignments and Signal Levels for 15 pin RGB AnalogCable Management Creating a video wallPFP Controller Installation & Overall Description Front Panel PFP Controller DescriptionRGB Output Video Inputs Rear PanelPFP Controller Remote Description Connection Examples Quick Set-up GuideMain Menu Menu TreePicture Quality Adjustments Page Page Side Bar Level Installation MenuInvert Output Shift Input ShiftIR Code Select System Reset BlankingBlanking Basic Operations To check the remaining time To set the off timerTo cancel the off timer After the power is turned off with the off timerWide Operations When viewing videos or digital video discs Picture Size setting Wide Screen Operation with Computer SignalsWhen Picture Size is set to OFF Supported resolutionMenu Operations Advanced menu modeMenu Tree ResetOPTION2 PWR. MGT Adjusting the picture Picture Settings MenuSetting the color temperature Adjusting the color to the desired levelReducing noise in the picture LOW Tone settings Making the Low Tone adjustments Adjusting the white balance Gamma settings Audio settings menu Audio Settings MenuAdjusting the colors Color Tune settingsExample Setting Audio INPUT1 to Video Image Adjust Settings MenuSetting the allocation of the audio connectors Adjusting the Position, Size, Fine Picture, Picture AdjSetting the on-screen menu Option1 Settings Menu OSM Orbiter settings Setting the BNC connectorsChecking the signal being transmitted to RGB1 terminal Setting a computer image to the correct RGB select screen RGB Select modes Setting high definition images to the suitable screen sizeSetting the Input Skip Input Skip settingsOption2 Settings Menu Resetting to the default valuesSetting the power management for computer images Reducing burn-in of the screen POWER/STANDBY indicatorSetting the picture to suit the movie PLE settings Orbiter settings Orbiter Function settings Inverse Settings Setting the time To select on for the Working TimeScreen Wiper Gray Level settings Setting the screen size for S1/S2 video input Soft Focus settings Setting the gray level for the sides of the screen PLUG/PLAY settings Setting the picture size for RGB input signalsSetting the signal and black level for DVI signal S1/S2 settingsPresent Time Option3 Settings MenuUsing the timer Present Time settings Special characters in the Program Timer screen Setting the power on mode To reset the program To reset the data IR Remote settings Enabling/disabling remote control wireless transmission PWR. on Mode settings Control Lock settingsID number setting Loop Out settingScreens Video Wall setting Divider settings Video Wall Position settings Auto ID settings DISP. Mode settings Image Adjust settings PLE Link On Delay Power on delay P. on Delay settings PLE Link settings Repeat Timer settings Advanced OSM Settings MenuSetting the menu mode Repeat TimerSetting the video signal format Language Settings MenuColor System Settings Menu Setting the language for the menusCommunication Parameters External ControlApplication ConnectionsTable of Signals Supported Supported resolutionComputer input signals supported by this system General Information PFP Controller RS-232 CommunicationsParameter min/max Value stored? PFP Controller RS-232 CommandsStore YES Symptom Checks Remedy TroubleshootingPage Plasma does not turn on After initial installation.Power LED on the front Yellow after the power buttonDefinition in the bright On, and the power LED onImage appears too Bright, and there is a loss169 Weight 140 lbs .5 kg1366 x DiagonalPfptm Controller Specifications & Dimensions RUMA-006830-SPL