Runco PL-61CX manual Menu Tree, Main Menu

Page 27

Menu Description and Navigation

Menu Tree

INPUT SELECT

 

Standard Video:

 

> Composite

 

S-Video

 

Component

Brightness

 

High Definition:

Contrast

 

Component

Anamorphic

RGB

 

Standard 4:3

ASPECT RATIO SELECT

Letterbox

 

Virtual Wide

INSTALLER ADJUST*

 

*Menus are only available during “Installer Mode”.

Tint

Color

Brightness

Contrast

Sharpness

Luma Enhance*

Chroma Enhance*

Color Balance*

Side Bar Level

InvertOff

Output Shift

Input Shift

Blanking

IR Code Select

Red Gain

Green Gain

Blue Gain

Red Offset

Green Offset

Blue Offset

The menu tree above is an overall glance at the menu system in the PL-61cx. The description of the menus and their functions are below.

Main Menu

The main menu includes three main sections: INPUT SELECT (Composite, S-video, Component, HD Component, HD RGB), ASPECT RATIO SELECT and INSTALLER ADJUST.

These menus are described in detail below:

INPUT SELECT is done by highlighting the desired source with the up or down arrows and pressing ENTER. Sources may also be selected by pressing the left or right arrows on the front panel or remote, or by one of the direct access buttons on the remote. High Definition or progressive DVD signals are input to the HDTV port.

ASPECT RATIO SELECT is done by highlighting 'Aspect Ratio' on the main menu and pressing enter. The Aspect Ratio menu will then appear; and either ANAMORPHIC, STANDARD 4:3, LETTERBOX or VIRTUAL WIDE may be selected. Aspect ratios may also be selected by pressing either the up or down arrow buttons, or by one of the direct access buttons on the remote.

INSTALLER ADJUST is used for adjustments usually made during the initial installation. This includes Image Shift, Blanking, Side Bar Level and IR Code Select.

17

Image 27
Contents PL-61cx Table of Contents External Control Options Features you’ll enjoy includeContents of the package IntroductionPrecautions Important InformationRisk of Electric Shock Do not Open Plasma monitor cleaning procedure To avoid damage and prolong operating lifeRecommendations to avoid or minimize phosphor burn-in Three Year Limited Warranty RIGHTS, Limits and Exclusions TWO Year Limited Warranty RIGHTS, Limits and Exclusions How to Attach Options to the Plasma Monitor Part Names and Function Turns the plasma monitor’s power on and offReceives the signals from the remote control Sets the On-Screen Menu mode and displays the main menuConnect the included power cord here Rear View / Terminal BoardConnect DVD’s, High Definition or Laser Discs, etc here Installation Remote Control Use of Installation Remote Control Battery Installation and Replacement Using the wired remote control mode Operating Range1/8 Stereo Mini cable must be purchased separeately Video Plasma Monitor InstallationConnections with Equipment that have a Digital Interface Connecting Your Document CameraConnecting Your VCR or Laser Disc Player Connecting Your DVD PlayerPin No Signal Analog Pin Assignments and Signal Levels for 15 pin RGB AnalogCable Management Creating a video wallPFP Controller Installation & Overall Description Front Panel PFP Controller DescriptionRGB Output Video Inputs Rear PanelPFP Controller Remote Description Connection Examples Quick Set-up GuideMain Menu Menu TreePicture Quality Adjustments Page Page Side Bar Level Installation MenuInvert Output Shift Input ShiftIR Code Select System Reset BlankingBlanking Basic Operations To check the remaining time To set the off timerTo cancel the off timer After the power is turned off with the off timerWide Operations When viewing videos or digital video discs Picture Size setting Wide Screen Operation with Computer SignalsWhen Picture Size is set to OFF  Supported resolutionMenu Operations  Advanced menu modeMenu Tree ResetOPTION2 PWR. MGT Adjusting the picture Picture Settings MenuSetting the color temperature Adjusting the color to the desired levelReducing noise in the picture  LOW Tone settings Making the Low Tone adjustments Adjusting the white balance  Gamma settings Audio settings menu Audio Settings MenuAdjusting the colors  Color Tune settingsExample Setting Audio INPUT1 to Video Image Adjust Settings MenuSetting the allocation of the audio connectors Adjusting the Position, Size, Fine Picture, Picture AdjSetting the on-screen menu Option1 Settings Menu OSM Orbiter settings Setting the BNC connectorsChecking the signal being transmitted to RGB1 terminal Setting a computer image to the correct RGB select screen RGB Select modes Setting high definition images to the suitable screen sizeSetting the Input Skip  Input Skip settingsOption2 Settings Menu Resetting to the default valuesSetting the power management for computer images Reducing burn-in of the screen POWER/STANDBY indicatorSetting the picture to suit the movie  PLE settings Orbiter settings  Orbiter Function settings Inverse Settings  Setting the time  To select on for the Working TimeScreen Wiper  Gray Level settings Setting the screen size for S1/S2 video input Soft Focus settings Setting the gray level for the sides of the screen PLUG/PLAY settings Setting the picture size for RGB input signalsSetting the signal and black level for DVI signal  S1/S2 settingsPresent Time Option3 Settings MenuUsing the timer  Present Time settings Special characters in the Program Timer screen Setting the power on mode To reset the program  To reset the data IR Remote settings Enabling/disabling remote control wireless transmission PWR. on Mode settings  Control Lock settingsID number setting Loop Out settingScreens Video Wall setting Divider settings  Video Wall Position settings Auto ID settings  DISP. Mode settings Image Adjust settings PLE Link On Delay Power on delay P. on Delay settings  PLE Link settings Repeat Timer settings Advanced OSM Settings MenuSetting the menu mode Repeat TimerSetting the video signal format Language Settings MenuColor System Settings Menu Setting the language for the menusCommunication Parameters External ControlApplication ConnectionsTable of Signals Supported Supported resolutionComputer input signals supported by this system General Information PFP Controller RS-232 CommunicationsParameter min/max Value stored? PFP Controller RS-232 CommandsStore YES Symptom Checks Remedy TroubleshootingPage Plasma does not turn on After initial installation.Power LED on the front Yellow after the power buttonDefinition in the bright On, and the power LED onImage appears too Bright, and there is a loss169 Weight 140 lbs .5 kg1366 x DiagonalPfptm Controller Specifications & Dimensions RUMA-006830-SPL