Runco PL-61CX manual Setting the screen size for S1/S2 video input,  Soft Focus settings

Page 54

Information

Setting the time

WORKING TIME

Set the time duration for “SCREEN

 

WIPER”.

 

When the WORKING TIME is set

 

to “ON” the mode will stay on.

WAITING TIME

Set the standby time until the

 

“SCREEN WIPER” mode starts.

SPEED

Set the moving speed for the

 

“SCREEN WIPER”. The speed

 

decreases as the number increases.

*The “WAITING TIME” can not be set when the “WORKING TIME” is ON.

*THE “WORKING TIME” and “WAITING TIME” can be set for up to 12 hours and 45 minutes in units of 3 minutes.

SOFT FOCUS

Reduces edges and softens the image.

Example: Setting “SOFT FOCUS” to “2”

Perform Steps 1-2 of LONG LIFE, then...

3.Use the ▲ and ▼ buttons to select “SOFT FOCUS”.

4.Use the  and  buttons to select “2”.

The mode switches as follows each time the  or  button is pressed:

→OFF ↔ 1 ↔ 2 ↔ 3 ↔ 4

 

 

 

LONG LIFE

 

 

PLE

:

AUTO

ORBITER

:

OFF

INVERSE

:

OFF

SCREEN WIPER

:

OFF

 

SOFT FOCUS

 

:

2

 

 

SEL.

ADJ.

 

RETURN

 

EXIT

Information

SOFT FOCUS settings

OFF ............ Turns the SOFT FOCUS function off.

1, 2, 3, 4 ..... Activates the SOFT FOCUS setting. The

higher numbers create a softer image. “SHARPNESS” can not be adjusted on the “PICTURE” menu.

Setting the gray level for the sides of the screen

Use this procedure to set the gray level for the parts on the screen on which nothing is displayed when the screen is set to the 4:3 size.

Example: Adjusting the “GRAY LEVEL”

Set “ADVANCED OSM” to “ON” in the main menu (1/ 2), then perform the following operations.

1.On the MAIN MENU, select “OPTION2”, then press the MENU/ENTER button.

The “OPTION2” screen appears.

2.Use the ▲ and ▼ buttons to select “GRAY LEVEL”.

3.To adjust the “GRAY LEVEL”...

Use the  and  buttons to adjust the GRAY LEVEL.

 

 

 

 

OPTION2

 

2 / 3

 

 

PREVIOUS PAGE

 

 

 

POWER MGT.

 

:

OFF

CINEMA MODE

 

:

ON

LONG LIFE

 

 

 

 

 

GRAY LEVEL

 

 

:

5

 

 

 

 

 

 

 

 

S1/S2

 

:

OFF

 

 

NEXT PAGE

 

 

 

 

 

 

SEL.

ADJ.

 

EXIT

RETURN

Information

GRAY LEVEL settings

This adjusts the brightness of the black (the gray level) for the sides of the screen.

The standard is 0 (black). The level can be adjusted from 0 to 15. The factory setting is 3 (dark gray).

Restoring the factory default settings

Select “ALL RESET” under the OPTION1 menu. Note that this also restores other settings to the factory defaults.

Setting the screen size for S1/S2 video input

If the S-video signal contains screen size information, the image will be automatically adjusted to fit the screen when this S1/S2 is set to AUTO.

This feature is available only when an S-video signal is input via the VIDEO3 terminal.

Example: Setting the “S1/S2” to “AUTO”

Set “ADVANCED OSM” to “ON” in the main menu (1/ 2), then perform the following operations.

1.On the MAIN MENU, select “OPTION2”, then press the MENU/ENTER button.

The “OPTION2” screen appears.

2.Use the ▲ and ▼ buttons to select “S1/S2”.

3.Use the  and  buttons to select “AUTO”.

The mode switches as follows each time the  or  button is pressed:

OFF ↔ AUTO

 

 

 

OPTION2

 

2 / 3

 

PREVIOUS PAGE

 

 

 

POWER MGT.

 

:

OFF

CINEMA MODE

 

:

ON

LONG LIFE

 

 

 

 

GRAY LEVEL

 

:

3

 

 

S1/S2

 

 

:

AUTO

 

NEXT PAGE

 

 

 

 

 

SEL.

ADJ.

 

EXIT

RETURN

44

Page 53 Page 55
Image 54
Page 53 Page 55
Contents PL-61cx Table of Contents External Control Introduction Features you’ll enjoy includeContents of the package OptionsPrecautions Important InformationRisk of Electric Shock Do not Open Plasma monitor cleaning procedure To avoid damage and prolong operating lifeRecommendations to avoid or minimize phosphor burn-in Three Year Limited Warranty RIGHTS, Limits and Exclusions TWO Year Limited Warranty RIGHTS, Limits and Exclusions How to Attach Options to the Plasma Monitor Sets the On-Screen Menu mode and displays the main menu Turns the plasma monitor’s power on and offReceives the signals from the remote control Part Names and FunctionConnect the included power cord here Rear View / Terminal BoardConnect DVD’s, High Definition or Laser Discs, etc here Installation Remote Control Use of Installation Remote Control Battery Installation and Replacement Using the wired remote control mode Operating Range1/8 Stereo Mini cable must be purchased separeately Plasma Monitor Installation VideoConnecting Your DVD Player Connecting Your Document CameraConnecting Your VCR or Laser Disc Player Connections with Equipment that have a Digital InterfacePin Assignments and Signal Levels for 15 pin RGB Analog Pin No Signal AnalogCreating a video wall Cable ManagementPFP Controller Installation & Overall Description PFP Controller Description Front PanelRear Panel RGB Output Video InputsPFP Controller Remote Description Quick Set-up Guide Connection ExamplesMenu Tree Main MenuPicture Quality Adjustments Page Page Installation Menu Side Bar LevelInvert Output Shift Input ShiftIR Code Select System Reset BlankingBlanking Basic Operations After the power is turned off with the off timer To set the off timerTo cancel the off timer To check the remaining timeWhen viewing videos or digital video discs Wide Operations Supported resolution Wide Screen Operation with Computer SignalsWhen Picture Size is set to OFF  Picture Size setting Advanced menu mode Menu OperationsReset Menu TreeOPTION2 PWR. MGT Picture Settings Menu Adjusting the pictureSetting the color temperature Adjusting the color to the desired levelReducing noise in the picture  Gamma settings Making the Low Tone adjustments Adjusting the white balance  LOW Tone settings Color Tune settings Audio Settings MenuAdjusting the colors  Audio settings menuAdjusting the Position, Size, Fine Picture, Picture Adj Image Adjust Settings MenuSetting the allocation of the audio connectors Example Setting Audio INPUT1 to VideoOption1 Settings Menu Setting the on-screen menuSetting a computer image to the correct RGB select screen Setting the BNC connectorsChecking the signal being transmitted to RGB1 terminal  OSM Orbiter settings Input Skip settings Setting high definition images to the suitable screen sizeSetting the Input Skip  RGB Select modesOption2 Settings Menu Resetting to the default valuesSetting the power management for computer images  PLE settings POWER/STANDBY indicatorSetting the picture to suit the movie Reducing burn-in of the screen Orbiter settings  Orbiter Function settings Inverse Settings  Setting the time  To select on for the Working TimeScreen Wiper Setting the gray level for the sides of the screen Setting the screen size for S1/S2 video input Soft Focus settings  Gray Level settings S1/S2 settings Setting the picture size for RGB input signalsSetting the signal and black level for DVI signal  PLUG/PLAY settings Present Time settings Option3 Settings MenuUsing the timer Present Time To reset the data Setting the power on mode To reset the program  Special characters in the Program Timer screen Control Lock settings Enabling/disabling remote control wireless transmission PWR. on Mode settings  IR Remote settingsLoop Out setting ID number setting Video Wall Position settings Video Wall setting Divider settings Screens Auto ID settings  DISP. Mode settings Image Adjust settings  PLE Link settings On Delay Power on delay P. on Delay settings PLE LinkRepeat Timer Advanced OSM Settings MenuSetting the menu mode  Repeat Timer settingsSetting the language for the menus Language Settings MenuColor System Settings Menu Setting the video signal formatConnections External ControlApplication Communication ParametersTable of Signals Supported Supported resolutionComputer input signals supported by this system PFP Controller RS-232 Communications General InformationPFP Controller RS-232 Commands Parameter min/max Value stored?Store YES Troubleshooting Symptom Checks RemedyPage Yellow after the power button After initial installation.Power LED on the front Plasma does not turn onBright, and there is a loss On, and the power LED onImage appears too Definition in the brightDiagonal Weight 140 lbs .5 kg1366 x 169Pfptm Controller Specifications & Dimensions RUMA-006830-SPL
Top Page Image Contents