Runco PL-61CX manual Option3 Settings Menu, Using the timer,  Present Time settings

Page 56

Option3 Settings Menu

Using the timer

This function sets the monitor to turn ON/OFF automatically at a set time.

Set “ADVANCED OSM” to “ON” in the main menu (1/ 2), then perform the following operations.

1.On the MAIN MENU, select “OPTION3”, then press the MENU/ENTER button.

The “OPTION3” screen appears.

2.Use the and buttons to select “TIMER”, then press the MENU/ENTER button.

The “TIMER” screen appears.

 

TIMER

PRESENT TIME

 

PROGRAM

: OFF

SEL.

MENU/ENTER

OK

EXIT

RETURN

3.Set the TIMER using ▲▼  and  buttons. See page 32 to set PRESENT TIME.

See page 33 to set PROGRAM.

Information

Restoring the factory default settings

Select “ALL RESET” under the OPTION1 menu. Note that this also restores other settings to the factory defaults.

PRESENT TIME

This sets the day of the week and present time.

Example: Setting “WEDNESDAY”, “22:05”

Perform Steps 1-2 of TIMER, then...

3.Use the and buttons to select “PRESENT TIME”, then press the MENU/ENTER button.

The “PRESENT TIME” screen appears.

 

PRESENT TIME

RETURN

 

 

 

DAYLIGHT

 

 

 

SAVING TIME

:

OFF

 

WEDNESDAY

 

 

 

13 : 00 : 00

 

 

SEL.

 

 

RETURN

ADJ.

EXIT

4.Use the and buttons to select the item, then adjust using the  and  buttons.

 

PRESENT TIME

RETURN

 

 

 

 

DAYLIGHT

 

 

 

 

SAVING TIME

:

OFF

 

WEDNESDAY

 

 

 

 

22 : 05 : 00

 

 

SEL.

 

 

 

RETURN

ADJ.

EXIT

The mode switches as follows each time the  or  button is pressed:

• DAYLIGHT SAVING TIME

ON OFF

• Day

SUNDAY MONDAY ..... FRIDAY SATURDAY

• Hour/Minutes

00:00 00:01 00:02 ..... 23:58 23:59

5.Once the setting is completed...

Use the and buttons to select “SET”, then press the MENU/ENTER button.

The adjustments are stored and return to the TIMER menu.

 

 

 

 

PRESENT TIME

RETURN

 

 

 

 

 

DAYLIGHT

 

 

 

 

 

 

SAVING TIME

:

OFF

 

 

 

 

WEDNESDAY

 

 

 

 

 

 

22 : 05 : 00

 

 

 

 

 

 

 

 

 

 

SET

 

 

 

 

 

 

SEL.

MENU/ENTER

OK

EXIT

RETURN

Information

PRESENT TIME settings

DAYLIGHT SAVING TIME

........................

Use to set DAYLIGHT SAVING

 

TIME.

 

ON: The present time + 1 hour.

 

OFF: Cancelled

Day

Set the day of the week (e.g. Sunday).

Hour

Set the hour in the 24-hour format

 

(range 00 to 23).

Minutes

Set the minutes (range 00 to 59).

*If you press the EXIT button instead of the MENU/ ENTER button in step 5, the settings can not be mode.

46

Image 56
Contents PL-61cx Table of Contents External Control Features you’ll enjoy include Contents of the packageIntroduction OptionsRisk of Electric Shock Do not Open PrecautionsImportant Information Recommendations to avoid or minimize phosphor burn-in Plasma monitor cleaning procedureTo avoid damage and prolong operating life Three Year Limited Warranty RIGHTS, Limits and Exclusions TWO Year Limited Warranty RIGHTS, Limits and Exclusions How to Attach Options to the Plasma Monitor Turns the plasma monitor’s power on and off Receives the signals from the remote controlSets the On-Screen Menu mode and displays the main menu Part Names and FunctionConnect DVD’s, High Definition or Laser Discs, etc here Connect the included power cord hereRear View / Terminal Board Installation Remote Control Use of Installation Remote Control Battery Installation and Replacement 1/8 Stereo Mini cable must be purchased separeately Using the wired remote control modeOperating Range Plasma Monitor Installation VideoConnecting Your Document Camera Connecting Your VCR or Laser Disc PlayerConnecting Your DVD Player Connections with Equipment that have a Digital InterfacePin Assignments and Signal Levels for 15 pin RGB Analog Pin No Signal AnalogCreating a video wall Cable ManagementPFP Controller Installation & Overall Description PFP Controller Description Front PanelRear Panel RGB Output Video InputsPFP Controller Remote Description Quick Set-up Guide Connection ExamplesMenu Tree Main MenuPicture Quality Adjustments Page Page Installation Menu Side Bar LevelInvert IR Code Select Output ShiftInput Shift Blanking System ResetBlanking Basic Operations To set the off timer To cancel the off timerAfter the power is turned off with the off timer To check the remaining timeWhen viewing videos or digital video discs Wide OperationsWide Screen Operation with Computer Signals When Picture Size is set to OFF Supported resolution  Picture Size setting Advanced menu mode Menu OperationsReset Menu TreeOPTION2 PWR. MGT Picture Settings Menu Adjusting the pictureReducing noise in the picture Setting the color temperatureAdjusting the color to the desired level Making the Low Tone adjustments  Adjusting the white balance Gamma settings  LOW Tone settingsAudio Settings Menu Adjusting the colors Color Tune settings  Audio settings menuImage Adjust Settings Menu Setting the allocation of the audio connectorsAdjusting the Position, Size, Fine Picture, Picture Adj Example Setting Audio INPUT1 to VideoOption1 Settings Menu Setting the on-screen menuSetting the BNC connectors Checking the signal being transmitted to RGB1 terminalSetting a computer image to the correct RGB select screen  OSM Orbiter settingsSetting high definition images to the suitable screen size Setting the Input Skip Input Skip settings  RGB Select modesSetting the power management for computer images Option2 Settings MenuResetting to the default values POWER/STANDBY indicator Setting the picture to suit the movie PLE settings Reducing burn-in of the screen Inverse Settings  Orbiter settings Orbiter Function settings Screen Wiper  Setting the time To select on for the Working Time Setting the screen size for S1/S2 video input  Soft Focus settingsSetting the gray level for the sides of the screen  Gray Level settingsSetting the picture size for RGB input signals Setting the signal and black level for DVI signal S1/S2 settings  PLUG/PLAY settingsOption3 Settings Menu Using the timer Present Time settings Present TimeSetting the power on mode  To reset the program To reset the data  Special characters in the Program Timer screenEnabling/disabling remote control wireless transmission  PWR. on Mode settings Control Lock settings  IR Remote settingsLoop Out setting ID number settingVideo Wall setting  Divider settings Video Wall Position settings Screens Image Adjust settings  Auto ID settings DISP. Mode settings On Delay Power on delay  P. on Delay settings PLE Link settings PLE LinkAdvanced OSM Settings Menu Setting the menu modeRepeat Timer  Repeat Timer settingsLanguage Settings Menu Color System Settings MenuSetting the language for the menus Setting the video signal formatExternal Control ApplicationConnections Communication ParametersComputer input signals supported by this system Table of Signals SupportedSupported resolution PFP Controller RS-232 Communications General InformationPFP Controller RS-232 Commands Parameter min/max Value stored?Store YES Troubleshooting Symptom Checks RemedyPage After initial installation. Power LED on the frontYellow after the power button Plasma does not turn onOn, and the power LED on Image appears tooBright, and there is a loss Definition in the brightWeight 140 lbs .5 kg 1366 xDiagonal 169Pfptm Controller Specifications & Dimensions RUMA-006830-SPL