Runco PL-61CX manual Rear Panel, RGB Output Video Inputs

Page 24

Rear Panel

1	5
COMLINK OUT
12V FUSE
			RGB OUTPUT					VIDEO INPUTS
RS-232 IN	V	H	B	G	R	HDTV	Y	Pr	Pb S-VIDEO COMPOSITE

MASK SCREEN

12V TRIGGER

CAUTION	!
RISK OF ELECTRIC SHOCK
DO NOT OPEN
AVIS: RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. NO USER- SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE CENTER.

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

RUNCO INTERNATIONAL

UNION CITY, CA

MADE IN USA

AC 120V 60Hz, 15W

MADE IN USA

2

3

4

6

7

8

9

10

11

12

13

1.12v FUSE

This fuse protects the 12v outputs from the MASK and SCREEN jacks. (Screen Fuse: 5mm x 25mm, AGC, 0.5A, 250V, Fast Blow)

2.MASK

This is a 12V output that can be used to trigger curtains, lifts, etc. (1/4A maximum load).

3.SCREEN

This is a 12V output that can be used to trigger curatins, lifts, etc. (1/4A maximum load).

4.RS-232 IN

This is for systems using serial (RS-232) to control the PFP Controller.

5.COMLINK OUT

The output of this jack must be connected to the ComLink input of the PL-61cx Plasma monitor. If this is not connected, neither the Controller or the Plasma can operate.

6.RGB OUTPUT

This is the RGB output of the PFP Controller. Connect the RGB output of the Controller to the PL-61cx’s RGB BNC port.

7.HDTV/PROGRESSIVE DVD

This is the input for HDTV or progressive DVD sources.

If the signal is RGB, select ‘RGB HD’; if it is Component, select ‘Component HD’.

8.COMPONENT INPUT

This is the input for Component Video from sources such as DVD players.

Note: The component output from a DTV decoder or a progressive-scan DVD cannot be used with this port; it must be used with the HDTV port.

9.S-VIDEO INPUT

This is the input for S-Videofrom sources such as Satellite receivers, S-VHS VCR’s and DVD players.

10.COMPOSITE VIDEO INPUT

This is the input for Composite Video from sources such as laser disc players, VCRs and other misc. sources.

11.POWER INPUT

Plug in Main Power here.

12.115 VAC FUSE

This is the main AC Input fuse (.5A/250V).

13.MAIN POWER SWITCH

Disconnects or applies main power to the Controller.

14

Image 24

Contents PL-61cx Table of Contents External Control Features you’ll enjoy include Contents of the packageIntroduction OptionsPrecautions Important InformationRisk of Electric Shock Do not Open Plasma monitor cleaning procedure To avoid damage and prolong operating lifeRecommendations to avoid or minimize phosphor burn-in Three Year Limited Warranty RIGHTS, Limits and Exclusions TWO Year Limited Warranty RIGHTS, Limits and Exclusions How to Attach Options to the Plasma Monitor Turns the plasma monitor’s power on and off Receives the signals from the remote controlSets the On-Screen Menu mode and displays the main menu Part Names and FunctionConnect the included power cord here Rear View / Terminal BoardConnect DVD’s, High Definition or Laser Discs, etc here Installation Remote Control Use of Installation Remote Control Battery Installation and Replacement Using the wired remote control mode Operating Range1/8 Stereo Mini cable must be purchased separeately Plasma Monitor Installation VideoConnecting Your Document Camera Connecting Your VCR or Laser Disc PlayerConnecting Your DVD Player Connections with Equipment that have a Digital InterfacePin Assignments and Signal Levels for 15 pin RGB Analog Pin No Signal AnalogCreating a video wall Cable ManagementPFP Controller Installation & Overall Description PFP Controller Description Front PanelRear Panel RGB Output Video InputsPFP Controller Remote Description Quick Set-up Guide Connection ExamplesMenu Tree Main MenuPicture Quality Adjustments Page Page Installation Menu Side Bar LevelInvert Output Shift Input ShiftIR Code Select System Reset BlankingBlanking Basic Operations To set the off timer To cancel the off timerAfter the power is turned off with the off timer To check the remaining timeWhen viewing videos or digital video discs Wide OperationsWide Screen Operation with Computer Signals When Picture Size is set to OFF Supported resolution Picture Size setting Advanced menu mode Menu OperationsReset Menu TreeOPTION2 PWR. MGT Picture Settings Menu Adjusting the pictureSetting the color temperature Adjusting the color to the desired levelReducing noise in the picture Making the Low Tone adjustments Adjusting the white balance Gamma settings LOW Tone settingsAudio Settings Menu Adjusting the colors Color Tune settings Audio settings menuImage Adjust Settings Menu Setting the allocation of the audio connectorsAdjusting the Position, Size, Fine Picture, Picture Adj Example Setting Audio INPUT1 to VideoOption1 Settings Menu Setting the on-screen menuSetting the BNC connectors Checking the signal being transmitted to RGB1 terminalSetting a computer image to the correct RGB select screen OSM Orbiter settingsSetting high definition images to the suitable screen size Setting the Input Skip Input Skip settings RGB Select modesOption2 Settings Menu Resetting to the default valuesSetting the power management for computer images POWER/STANDBY indicator Setting the picture to suit the movie PLE settings Reducing burn-in of the screen Orbiter settings Orbiter Function settings Inverse Settings Setting the time To select on for the Working TimeScreen Wiper Setting the screen size for S1/S2 video input Soft Focus settingsSetting the gray level for the sides of the screen Gray Level settingsSetting the picture size for RGB input signals Setting the signal and black level for DVI signal S1/S2 settings PLUG/PLAY settingsOption3 Settings Menu Using the timer Present Time settings Present TimeSetting the power on mode To reset the program To reset the data Special characters in the Program Timer screenEnabling/disabling remote control wireless transmission PWR. on Mode settings Control Lock settings IR Remote settingsLoop Out setting ID number settingVideo Wall setting Divider settings Video Wall Position settings Screens Auto ID settings DISP. Mode settings Image Adjust settings On Delay Power on delay P. on Delay settings PLE Link settings PLE LinkAdvanced OSM Settings Menu Setting the menu modeRepeat Timer Repeat Timer settingsLanguage Settings Menu Color System Settings MenuSetting the language for the menus Setting the video signal formatExternal Control ApplicationConnections Communication ParametersTable of Signals Supported Supported resolutionComputer input signals supported by this system PFP Controller RS-232 Communications General InformationPFP Controller RS-232 Commands Parameter min/max Value stored?Store YES Troubleshooting Symptom Checks RemedyPage After initial installation. Power LED on the frontYellow after the power button Plasma does not turn onOn, and the power LED on Image appears tooBright, and there is a loss Definition in the brightWeight 140 lbs .5 kg 1366 xDiagonal 169Pfptm Controller Specifications & Dimensions RUMA-006830-SPL