Runco PL-61CX manual

Page 30

SHARPNESS adjusts the amount of high-frequency detail in the image. This can be adjusted to the prefer- ence of the user. Keep in mind that when SHARPNESS is decreased, fine details in the image will become 'soft'; when it is increased, fine details will become sharper but will also make the picture appear 'noisy' if adjusted too high.

LUMA ENHANCE acts as an edge enhancement, especially around black to white transitions in the image. Essentially, this has the same characteristics as sharpness but affects the edges of objects far more that the rest of the image.

FREQUENCIES HIGH/LOW affect the overall range of the LUMA ENHANCE feature. For example, if using a lower-quality video source such as a VCR, the FREQUENCIES should be set to LOW. For a good quali- ty source such as a DVD player, set FREQUENCIES to HIGH. To set FREQUENCIES, press ENTER while LUMA ENHANCE is on-screen.

Note: Luma Enhance will only appear in the menu after the installation mode has been enabled.

CHROMA ENHANCE acts as an edge enhancement, especially around color transitions in the image. Essentially, this has the same characteristics as sharpness but affects the edges of objects far more that the rest of the image.

FREQUENCIES HIGH/LOW affect the overall range of the CHROMA ENHANCE feature. For example, if using a lower-quality video source such as a VCR, the FREQUENCIES should be set to LOW. For a good quality source such as a DVD player, set FREQUENCIES to HIGH. To set FREQUENCIES, press ENTER while CHROMA ENHANCE is on-screen.

Note: Chroma Enhance will only appear in the menu after the installation mode has been enabled.

COLOR BALANCE sets the overall color temperature of the image. When Color Balance is selected, you will get a menu with Red Gain, Green Gain, Blue Gain, Red Offset, Green Offset and Blue Offset. The Gain Controls increase or decrease the amount of that color in the brightest areas of the image; the Offset Controls affect the darkest areas. This should be adjusted using a gray scale or Pluge pattern for best results.

Note: Color Balance will only appear in the menu after the installation mode has been enabled.

20

Image 30

Contents PL-61cx Table of Contents External Control Introduction Features you’ll enjoy includeContents of the package OptionsPrecautions Important InformationRisk of Electric Shock Do not Open Plasma monitor cleaning procedure To avoid damage and prolong operating lifeRecommendations to avoid or minimize phosphor burn-in Three Year Limited Warranty RIGHTS, Limits and Exclusions TWO Year Limited Warranty RIGHTS, Limits and Exclusions How to Attach Options to the Plasma Monitor Sets the On-Screen Menu mode and displays the main menu Turns the plasma monitor’s power on and offReceives the signals from the remote control Part Names and FunctionConnect the included power cord here Rear View / Terminal BoardConnect DVD’s, High Definition or Laser Discs, etc here Installation Remote Control Use of Installation Remote Control Battery Installation and Replacement Using the wired remote control mode Operating Range1/8 Stereo Mini cable must be purchased separeately Plasma Monitor Installation VideoConnecting Your DVD Player Connecting Your Document CameraConnecting Your VCR or Laser Disc Player Connections with Equipment that have a Digital InterfacePin Assignments and Signal Levels for 15 pin RGB Analog Pin No Signal AnalogCreating a video wall Cable ManagementPFP Controller Installation & Overall Description PFP Controller Description Front PanelRear Panel RGB Output Video InputsPFP Controller Remote Description Quick Set-up Guide Connection ExamplesMenu Tree Main MenuPicture Quality Adjustments Page Page Installation Menu Side Bar LevelInvert Output Shift Input ShiftIR Code Select System Reset BlankingBlanking Basic Operations After the power is turned off with the off timer To set the off timerTo cancel the off timer To check the remaining timeWhen viewing videos or digital video discs Wide Operations Supported resolution Wide Screen Operation with Computer SignalsWhen Picture Size is set to OFF Picture Size setting Advanced menu mode Menu OperationsReset Menu TreeOPTION2 PWR. MGT Picture Settings Menu Adjusting the pictureSetting the color temperature Adjusting the color to the desired levelReducing noise in the picture Gamma settings Making the Low Tone adjustments Adjusting the white balance LOW Tone settings Color Tune settings Audio Settings MenuAdjusting the colors Audio settings menuAdjusting the Position, Size, Fine Picture, Picture Adj Image Adjust Settings MenuSetting the allocation of the audio connectors Example Setting Audio INPUT1 to VideoOption1 Settings Menu Setting the on-screen menuSetting a computer image to the correct RGB select screen Setting the BNC connectorsChecking the signal being transmitted to RGB1 terminal OSM Orbiter settings Input Skip settings Setting high definition images to the suitable screen sizeSetting the Input Skip RGB Select modesOption2 Settings Menu Resetting to the default valuesSetting the power management for computer images PLE settings POWER/STANDBY indicatorSetting the picture to suit the movie Reducing burn-in of the screen Orbiter settings Orbiter Function settings Inverse Settings Setting the time To select on for the Working TimeScreen Wiper Setting the gray level for the sides of the screen Setting the screen size for S1/S2 video input Soft Focus settings Gray Level settings S1/S2 settings Setting the picture size for RGB input signalsSetting the signal and black level for DVI signal PLUG/PLAY settings Present Time settings Option3 Settings MenuUsing the timer Present Time To reset the data Setting the power on mode To reset the program Special characters in the Program Timer screen Control Lock settings Enabling/disabling remote control wireless transmission PWR. on Mode settings IR Remote settingsLoop Out setting ID number setting Video Wall Position settings Video Wall setting Divider settings Screens Auto ID settings DISP. Mode settings Image Adjust settings PLE Link settings On Delay Power on delay P. on Delay settings PLE LinkRepeat Timer Advanced OSM Settings MenuSetting the menu mode Repeat Timer settingsSetting the language for the menus Language Settings MenuColor System Settings Menu Setting the video signal formatConnections External ControlApplication Communication ParametersTable of Signals Supported Supported resolutionComputer input signals supported by this system PFP Controller RS-232 Communications General InformationPFP Controller RS-232 Commands Parameter min/max Value stored?Store YES Troubleshooting Symptom Checks RemedyPage Yellow after the power button After initial installation.Power LED on the front Plasma does not turn onBright, and there is a loss On, and the power LED onImage appears too Definition in the brightDiagonal Weight 140 lbs .5 kg1366 x 169Pfptm Controller Specifications & Dimensions RUMA-006830-SPL