Sharp AR-M205, AR-M160 Interrupting a Copy RUN, Press the Interrupt key to interrupt the copy run

Page 32

INTERRUPTING A COPY RUN

(Interrupt copying)

A copy run can be temporarily interrupted to allow another copy job to be performed. When the other job is finished, the copy run will resume using the original copy settings.

Note Interrupt copying is not possible when the user programs are being configured, or when automatic two-sided copying, sort/group copying, or 2 IN 1 / 4 IN 1 copying is being performed.

1 Press the [INTERRUPT] key to interrupt the copy run.

 

The INTERRUPT

 

indicator will light up and

INTERRUPT

the display will show "0".

 

The INTERRUPT

 

indicator will blink until

 

the page that was being

 

copied when the

 

[INTERRUPT] key was

 

pressed is finished.

If the SPF/RSPF is being used, the copy

Note

run will not stop until the set number of

 

copies is completed.

If auditing mode is enabled:

"- - -" will appear in the number of copies display. Enter your 3-digit account number. Copying will not be possible unless a correct account number is entered. (p.00)

2 Remove the previous original(s) and place the original(s) of the interrupt copy job.

3 Press the [START] key ().

The copy will be

Cdelivered to the output

 

 

tray slightly offset from

 

 

the copies of the

B

 

interrupted run. (Shifter

A

function)

 

 

The Shifter function can

 

 

 

 

be disabled in the user

 

 

programs. (p.00)

A:Copies made before the interrupt copy job

B:Interrupt copy job

C:Copies made after the interrupt copy job

4 When the copy job is finished, press the [INTERRUPT] key and remove the original(s).

The INTERRUPT indicator will go off, indicating that the interrupt function is no longer operating. The copy settings will automatically revert to the settings selected for the copy run before the run was interrupted.

5 Replace the previous original(s) and press the [START] key ().

The interrupted copy run will resume.

30

Image 32
Contents AR-M160 AR-M205For Your Records Contents User Settings Important Points When Selecting AN Installation Site Do not install your machine in areas that areChanges, e.g., near an Air conditioner orSafety precautions Trademark acknowledgementsDo not touch the photoconductive drum green portion Scratches or smudges on the drum will cause dirty copiesUsing the Manual Online Manual on the accessory CD-ROMEnvironmental Information Meaning of R in Original and Paper Size IndicationsInch series and AB series metric references SPF and Rspf Standard FeaturesConventions Used in this Manual Main Features Part Names and Functions ExteriorInterior Operation Panel Zoom indicator 26 SPR/RSPF indicator when the SPF/RSPF is installedAuto Image key/indicator Paper feed location/misfeed location indicatorsPower on and OFF Power onPower OFF Power Save ModesType of paper Type of media Size Weight Capacity Feeding Loading PaperPaper Special papersImportant points when inserting paper in the bypass tray Loading PaperLoading the paper tray Fan the paperLoading the bypass tray Unfold the bypass trayPress the Start key and then the Paper Size Enter key Changing a TRAY’S Paper Size SettingUse the Original Size Enter key to select the paper size Original Placement Normal CopyingCopying from the document glass Open the document cover/SPF/RSPF, and place the originalPress the Start key to begin copying Select copy settingsCopying from the SPF/RSPF Set the originals face up in the document feeder tray Press the Start key and start copyingAuto tray switching Making a Copy Darker or LighterSelecting the Tray Original typesSetting the Number of Copies Important note when making a large number of copiesREDUCTION/ENLARGMENT/ZOOM Automatic Ratio SelectionSelecting a preset ratio Fine adjustment of the ratioManual Ratio Selection Press the Auto Image keyXY Zoom copying Press the Copy ratio display keyTWO-SIDED Copying Using the Bypass Tray Press the Start keyCopy original a Place original B as shown below Portrait-oriented originalInsert the paper all the way Copy is delivered to the output trayAutomatic TWO-SIDED Copying Using the document glass Using the SPF/RSPFIndicator blinks, and the original is scanned into memory Place originals in the SPF/RSPFImage Rotation in Duplex Copying Press a numeric key to enter the setting codePress the Original to Copy key to exit the setting Dual page Copying Replace the previous originals and press the Start key Interrupting a Copy RUNPress the Interrupt key to interrupt the copy run Rotating the Image 90 Degrees Sort Copy / Group CopyPress the Start key and place the next original Sort/Group copy using the document glassSort/Group copy using the SPF/RSPF 1/4 in 1 copy using the document glass Desired modeCopying Multiple Originals Onto a Single Sheet of Paper Press the 2 in 1/4 in 1 key to select1/4 in 1 copy using the SPF/RSPF Setting the layout patternUse the 2 in 1/4 in 1 key to access the setting Select the setting code by pressing a numeric keyCreating Margins When Copying Place the originals Select the margin positionPress the Margin Shift key Press the 1 key or the 2 key, and then press the Start keySelect the number of copies and other Settings, and press the Start keyErasing Shadows around the Edges of a Copy Make sure that paper is loaded in the tray Using the Printer ModeBasic Procedure for Printing Using the Scanner Mode Scanning Using the Keys on the MachinePress a Scan Menu key to begin scanning Scanning from Your ComputerScan Menu keys and the Button Manager scan menu Operation in COPY, PRINTER, and Scanner Modes During copyingPrinter During printing Scanner During scan previewPlace the original. p.00 Adjusting the Automatic Exposure LevelPress the AUTO/TEXT/PHOTO key to complete the setting Enabling Toner Save Mode Photo indicator stops blinking and lights steadilyCustomizing Settings User ProgramsLeft edge 2 10 mmPattern 300dpi 50%Minimum CopiesSelecting a Setting for a User Program Base settingsPress the Light key to complete the settings Enter the program number withSettings for Auditing Mode Auditing ModeAuditing Mode Settings Factory default settings Are indicated in bold EnablingEnter the program number with the numeric keys Selecting Auditing Mode SettingsEnter a setting for the selected program Enabling/disabling auditing mode Account number deletionAccount number entry Account number changeResetting account Copying when auditing mode is enabledTroubleshooting This chapter describes troubleshooting and misfeed removalMACHINE/COPYING Problems Paper properly installed? Pieces of paper inside machine?Paper misfeed Is too much paper loaded in the tray? Do some sheets of paper stick together?Are any other indicators lit? Is an interrupt copy job in progress?Is the output tray full? Is the tray out of paper?Printed image is dirty Printing and Scanning ProblemsPrinted image is light Is the orientation of document setting correct? Is the port setting correct?Has the printer driver been installed properly? Lines in tables are not alignedHave you specified a suitable resolution? Are the brightness and contrast settings suitable?Poor scanning quality Have you placed the original straight?Do you have Administrator rights? Is there enough computer memory?What to do when a notice page is printed Removing the softwareClick the start button, and then click Control Panel Click Add or Remove ProgramsIndicators and Display Messages Misfeed Removal Misfeed in the SPF/RSPFRemove the misfed original Section aSection C Misfeed indicator Stops blinking and copying can be resumedMisfeed in the Bypass Tray Close the front cover and side cover Misfeed in the MachineMisfeed in the paper feed area Misfeed in the fusing area Be careful not to tear the misfed paper during removal Misfeed in the transport areaClose the side cover by pressing the handle on the cover Push the paper tray in completely Misfeed in Paper TrayClose the paper tray Be careful not to tear Misfed paper during Removal Open the side cover Close the side coverRemove the misfed paper Toner cartridge replacement required Indicator will go out Replacing the Toner CartridgeClose the front cover Discard the shutterChecking the Total Output Count and Toner Level Checking the Total Output CountTotal output count Total copy countRoutine Maintenance Cleaning the Document GLASS/SPF/RSPF and Document CoverChecking the Toner Level Press the Light key to return to the normal displayCleaning the Bypass Tray Paper Feed Roller Cleaning the Transfer ChargerSingle Pass Feeder Reversing Single Pass Feeder SpecificationsPeripheral Devices Specification Sheet Paper Feed Unit 250-SHEET Paper Feed UnitDual Function Board Part namesSupply Types and Storage Proper StorageStore the supplies in a location that is Store paper in the wrapper and lying flatSpecifications Printer Function Scanner Function Software License Page Index Page Page Page Sharp Corporation
Related manuals
Manual 33 pages 13.5 Kb Manual 20 pages 22.01 Kb Manual 96 pages 12.14 Kb

AR-M205, AR-M160 specifications

The Sharp AR-M160 and AR-M205 are multifunctional copiers designed to meet the needs of small to medium-sized businesses. These models provide essential features that promote efficiency and productivity in any office environment. Both devices are equipped with advanced technologies that enhance their functionality and user-friendliness, making them ideal for daily document handling tasks.

One of the main features of the AR-M160 and AR-M205 is their impressive print and copy capabilities. The AR-M160 offers a print speed of up to 16 pages per minute, while the AR-M205 steps it up to an exceptional 20 pages per minute. This difference in speed can significantly impact workflow, especially in high-volume settings. Both models support a variety of paper sizes, including letter, legal, and A4, allowing users to manage diverse document tasks efficiently.

The AR-M160 and AR-M205 also provide excellent image quality, delivering sharp text and clear graphics. With a maximum print resolution of 1200 x 600 dots per inch, these machines ensure that every document produced is of professional quality. The advanced imaging technologies employed in these copiers, such as automatic exposure control and image processing, contribute to consistent and reliable results.

In terms of functionality, both the AR-M160 and the AR-M205 feature a user-friendly control panel that simplifies operation. The 7-inch color touchscreen provides intuitive navigation and easy access to various settings. Additionally, the devices support a range of finishing options, including stapling, hole-punching, and folding, allowing businesses to produce polished documents in-house.

Another notable characteristic of these models is their network connectivity. The AR-M160 and AR-M205 can be easily integrated into existing office networks, enabling users to print and scan documents from multiple devices. They support built-in network printing via Ethernet, as well as an optional wireless connection, ensuring flexibility and accessibility for all users.

Security is also a priority with these multifunction devices. They come equipped with various security features such as user authentication, secure print, and data encryption, which help protect sensitive information and ensure compliance with data protection regulations.

Overall, the Sharp AR-M160 and AR-M205 multifunction copiers embody reliability, efficiency, and high-quality output, making them valuable assets for any office environment. Their combination of advanced features, ease of use, and solid performance helps streamline document workflows and enhances productivity in today's fast-paced business world.