SUPER MICRO Computer I2DMR-8G2 user manual Static-Sensitive Devices, Precautions, Unpacking

Page 21

Chapter 2: Installation

Chapter 2

Installation

2-1 Static-Sensitive Devices

Electric-Static-Discharge (ESD) can damage electronic components. To pre- vent damage to your system board, it is important to handle it very carefully. The following measures are generally sufficient to protect your equipment from ESD.

Precautions

Use a grounded wrist strap designed to prevent static discharge.

Touch a grounded metal object before removing the board from the anti- static bag.

Handle the board by its edges only; do not touch its components, periph- eral chips, memory modules or gold contacts.

When handling chips or modules, avoid touching their pins.

Put the motherboard and peripherals back into their antistatic bags when not in use.

For grounding purposes, make sure your computer chassis provides ex- cellent conductivity between the power supply, the case, the mounting fasteners and the motherboard.

Unpacking

The motherboard is shipped in antistatic packaging to avoid static damage. When unpacking the board, make sure the person handling it is static protected.

2-1

Image 21
Contents Super Page Manual Organization About This ManualTable of Contents Table of Contents TroubleshootingAppendices BiosOverview ChecklistHeadquarters Contacting SupermicroEurope Asia-PacificSuper i2DMR-8G2/i2DMR-iG2 Image Super i2DMR-8G2/i2DMR-iG2 Motherboard Layout Jumper Description Default Setting Connector DescriptionQuick Reference i2DMR-8G2/i2DMR-iG2 Chipset Motherboard FeaturesM o r y Expansion SlotsPC Health Monitoring Acpi FeaturesThermal Control Onboard I/OOther DimensionsBlock Diagram of the i2DMR-8G2/i2DMR-iG2 Motherboard Major bus groups are Chipset OverviewSpecial Features PC Health MonitoringComplementary Components include Power Supply Acpi FeaturesAuto-Switching Voltage Regulator for the CPU Core CPU Overheat LED and ControlSuper I/O Page Precautions Static-Sensitive DevicesUnpacking Locating the components included in the shipping package Itanium2 Processor and Heatsink InstallationInstallation Installing Motherboard into chassis Installation Edge Connector Signal Pins Installing and securing the Power Pod onto the ItaniumPage Installing the Heatsink on the CPU*for CPU w/o Heatsink only Connecting AC Power to the motherboard and the Power Pods Installing DIMMs Dimm InstallationMemory Support I/O Port Locations and Definitions I/OPorts/Control Panel ConnectorsFront Control Panel U66 Speaker Connector CN4Connecting Cables Overheat LED OH HDD LEDReset Button Power ButtonUniversal Serial Bus USB0/1, USB2/3 Serial Ports Front Panel Universal Serial Bus HeaderGlan Ports Ethernet Chassis IntrusionFan Headers Speaker HeaderWake-On-Ring Power Fault ConnectorAlarm Reset SMB Power I2 CGlan Enable/Disable Jumper SettingsExplanation Jumpers Cmos ClearScsi Enable/Disable *i2DMR-8G2 only VGA Enable/DisableScsi Termination Enable/ Disable *i2DMR-8G2 only Watch DogOnboard Indicators Force-Power-On Enable DisableGlan LEDs IDE Connectors COM Port, IDE, Ipmi and Scsi ConnectionsCOM Port 1 J5 & COM Header J38 Ipmi Ultra 320 Scsi Connectors *i2DMR-8G2 onlyPage Troubleshooting Procedures Before Power OnNo Power Losing the System’s Setup Configuration Memory ErrorsNo Video Frequently Asked Questions Technical Support ProceduresReturning Merchandise for Service Introduction AmibiosLanguage Menu Main SetupBSP Information System Time/System DateAdvanced Bios Setup Super IO Configuration Sub MenuSetup Warning Serial Port1 Address/Serial Port2 Address IDE Configurations Sub MenuLBA/Large Mode TypeBlock Multi-Sector Transfer A.R.T. For Hard disk drives DMA Mode32Bit Data Transfer Armd Emulation TypeQuiet Boot Bios Settings ConfigurationAtapi Detect Time Out Atapi 80Pin Cable DetectionAdvanced System Health System Health MonitorPower Loss Control Peripheral Device ConfigurationWatch Dog Timer Watch Dog Timer ValueUBS Configuration USB FunctionLegacy USB Support PCI Latency Timer PCI/PnP ConfigurationAllocate IRQ to PCI VGA PCI IDE BusMasterSecurity Settings Load Fail-Safe Defaults Load Optimal DefaultsExit Options Exit Saving ChangesDiscarding Changes Introduction to the EFI Platform Flash AMI Bios Page Page Page Brief instruction for adding the Cdrom boot option in EFI Software Installation Page Checkpoint Code Description IA-32 Post CodesRegister for date and time next Monochrome mode and color mode settings next 47h 60h 95h Checkpoints Code Description Common Debug CodesSuper i2DMR-8G2/i2DMR-iG2 User’s Manual