SUPER MICRO Computer I2DMR-8G2 user manual Hdd Led, Overheat LED OH

Page 34

SUPER i2DMR-8G2/i2DMR-iG2 User's Manual

HDD LED

The HDD LED connection is located on pins 13 and 14 of U66. Attach the hard drive LED cable here to display disk activity (for any hard drives on the system, including SCSI, Serial ATA and IDE). See the table on the right for pin defini- tions.

HDD LED Pin

Definitions

(U66)

Pin

Number Definition

13Vcc

14HD Active

NIC1 LED

The NIC (Network Interface Con- troller) LED connection for the GLAN port is located on pins 11 and 12 of U66. Attach the NIC LED cable to display network activity. Refer to the table on the right for pin definitions.

NIC LED Pin

Definitions

(U66)

Pin

Number Definition

11Vcc

12GND

NIC2 LED

The NIC (Network Interface Con- troller) LED connection for the GLAN port is located on pins 9 and 10 of U66. Attach the NIC LED cable to display network activity. Refer to the table on the right for pin definitions.

NIC 2 LED Pin

Definitions

(U66)

Pin

Number Definition

9Vcc

10 GND

Overheat LED (OH)

Connect an LED to the OH connec- tion on pins 7 and 8 of U66 to pro- vide advanced warning of chassis overheating. Refer to the table on the right for pin definitions.

Overheat (OH) LED

Pin Definitions

(U66)

Pin

Number Definition

7Vcc

8GND

2-14

Image 34
Contents Super Page About This Manual Manual OrganizationTable of Contents Troubleshooting Table of ContentsBios AppendicesChecklist OverviewEurope Contacting SupermicroHeadquarters Asia-PacificSuper i2DMR-8G2/i2DMR-iG2 Image Super i2DMR-8G2/i2DMR-iG2 Motherboard Layout Connector Description Jumper Description Default SettingQuick Reference i2DMR-8G2/i2DMR-iG2 M o r y Motherboard FeaturesChipset Expansion SlotsThermal Control Acpi FeaturesPC Health Monitoring Onboard I/ODimensions OtherBlock Diagram of the i2DMR-8G2/i2DMR-iG2 Motherboard Chipset Overview Major bus groups arePC Health Monitoring Special FeaturesComplementary Components include Auto-Switching Voltage Regulator for the CPU Core Acpi FeaturesPower Supply CPU Overheat LED and ControlSuper I/O Page Static-Sensitive Devices PrecautionsUnpacking Itanium2 Processor and Heatsink Installation Locating the components included in the shipping packageInstallation Installing Motherboard into chassis Installation Installing and securing the Power Pod onto the Itanium Edge Connector Signal PinsPage Installing the Heatsink on the CPU*for CPU w/o Heatsink only Connecting AC Power to the motherboard and the Power Pods Dimm Installation Installing DIMMsMemory Support I/OPorts/Control Panel Connectors I/O Port Locations and DefinitionsSpeaker Connector CN4 Front Control Panel U66Connecting Cables HDD LED Overheat LED OHPower Button Reset ButtonUniversal Serial Bus USB0/1, USB2/3 Glan Ports Ethernet Front Panel Universal Serial Bus HeaderSerial Ports Chassis IntrusionSpeaker Header Fan HeadersWake-On-Ring Alarm Reset ConnectorPower Fault SMB Power I2 CExplanation Jumpers Jumper SettingsGlan Enable/Disable Cmos ClearScsi Termination Enable/ Disable *i2DMR-8G2 only VGA Enable/DisableScsi Enable/Disable *i2DMR-8G2 only Watch DogForce-Power-On Enable Disable Onboard IndicatorsGlan LEDs COM Port, IDE, Ipmi and Scsi Connections IDE ConnectorsCOM Port 1 J5 & COM Header J38 Ultra 320 Scsi Connectors *i2DMR-8G2 only IpmiPage Before Power On Troubleshooting ProceduresNo Power Memory Errors Losing the System’s Setup ConfigurationNo Video Technical Support Procedures Frequently Asked QuestionsReturning Merchandise for Service Amibios IntroductionBSP Information Main SetupLanguage Menu System Time/System DateSuper IO Configuration Sub Menu Advanced Bios SetupSetup Warning IDE Configurations Sub Menu Serial Port1 Address/Serial Port2 AddressType LBA/Large ModeBlock Multi-Sector Transfer 32Bit Data Transfer DMA ModeA.R.T. For Hard disk drives Armd Emulation TypeAtapi Detect Time Out Bios Settings ConfigurationQuiet Boot Atapi 80Pin Cable DetectionSystem Health Monitor Advanced System HealthWatch Dog Timer Peripheral Device ConfigurationPower Loss Control Watch Dog Timer ValueUSB Function UBS ConfigurationLegacy USB Support Allocate IRQ to PCI VGA PCI/PnP ConfigurationPCI Latency Timer PCI IDE BusMasterSecurity Settings Exit Options Load Optimal DefaultsLoad Fail-Safe Defaults Exit Saving ChangesDiscarding Changes Introduction to the EFI Platform Flash AMI Bios Page Page Page Brief instruction for adding the Cdrom boot option in EFI Software Installation Page IA-32 Post Codes Checkpoint Code DescriptionRegister for date and time next Monochrome mode and color mode settings next 47h 60h 95h Common Debug Codes Checkpoints Code DescriptionSuper i2DMR-8G2/i2DMR-iG2 User’s Manual