SUPER MICRO Computer I2DMR-8G2 user manual Installation

Page 23

Chapter 2: Installation

B. Installing the Heatsink Retention Mechanism on the Motherboard

1.Place the retention mechanism (P/N SKT-0147-RM-IT2) on the mother- board as shown in the picture below:

2.Secure the retention mechanism onto the motherboard by screwing three (3) 6-32 4.5MM screws into the mounting holes on the back of the motherboard.

1.) Place the retention mechanism on the motherboard

2.) Screw in three 6-32 4.5mm screws on the reverse side of the motherboard

2-3

Image 23

Contents Super Page Manual Organization About This ManualTable of Contents Table of Contents TroubleshootingAppendices BiosOverview ChecklistAsia-Pacific Contacting SupermicroHeadquarters EuropeSuper i2DMR-8G2/i2DMR-iG2 Image Super i2DMR-8G2/i2DMR-iG2 Motherboard Layout Quick Reference i2DMR-8G2/i2DMR-iG2 Jumper Description Default SettingConnector Description Expansion Slots Motherboard FeaturesChipset M o r yOnboard I/O Acpi FeaturesPC Health Monitoring Thermal ControlOther DimensionsBlock Diagram of the i2DMR-8G2/i2DMR-iG2 Motherboard Major bus groups are Chipset OverviewComplementary Components include Special FeaturesPC Health Monitoring CPU Overheat LED and Control Acpi FeaturesPower Supply Auto-Switching Voltage Regulator for the CPU CoreSuper I/O Page Unpacking PrecautionsStatic-Sensitive Devices Locating the components included in the shipping package Itanium2 Processor and Heatsink InstallationInstallation Installing Motherboard into chassis Installation Edge Connector Signal Pins Installing and securing the Power Pod onto the ItaniumPage Installing the Heatsink on the CPU*for CPU w/o Heatsink only Connecting AC Power to the motherboard and the Power Pods Memory Support Installing DIMMsDimm Installation I/O Port Locations and Definitions I/OPorts/Control Panel ConnectorsFront Control Panel U66 Speaker Connector CN4Connecting Cables Overheat LED OH HDD LEDUniversal Serial Bus USB0/1, USB2/3 Reset ButtonPower Button Chassis Intrusion Front Panel Universal Serial Bus HeaderSerial Ports Glan Ports EthernetWake-On-Ring Fan HeadersSpeaker Header SMB Power I2 C ConnectorPower Fault Alarm ResetCmos Clear Jumper SettingsGlan Enable/Disable Explanation JumpersWatch Dog VGA Enable/DisableScsi Enable/Disable *i2DMR-8G2 only Scsi Termination Enable/ Disable *i2DMR-8G2 onlyGlan LEDs Onboard IndicatorsForce-Power-On Enable Disable COM Port 1 J5 & COM Header J38 IDE ConnectorsCOM Port, IDE, Ipmi and Scsi Connections Ipmi Ultra 320 Scsi Connectors *i2DMR-8G2 onlyPage No Power Troubleshooting ProceduresBefore Power On No Video Losing the System’s Setup ConfigurationMemory Errors Frequently Asked Questions Technical Support ProceduresReturning Merchandise for Service Introduction AmibiosSystem Time/System Date Main SetupLanguage Menu BSP InformationSetup Warning Advanced Bios SetupSuper IO Configuration Sub Menu Serial Port1 Address/Serial Port2 Address IDE Configurations Sub MenuBlock Multi-Sector Transfer LBA/Large ModeType Armd Emulation Type DMA ModeA.R.T. For Hard disk drives 32Bit Data TransferAtapi 80Pin Cable Detection Bios Settings ConfigurationQuiet Boot Atapi Detect Time OutAdvanced System Health System Health MonitorWatch Dog Timer Value Peripheral Device ConfigurationPower Loss Control Watch Dog TimerLegacy USB Support UBS ConfigurationUSB Function PCI IDE BusMaster PCI/PnP ConfigurationPCI Latency Timer Allocate IRQ to PCI VGASecurity Settings Exit Saving Changes Load Optimal DefaultsLoad Fail-Safe Defaults Exit OptionsDiscarding Changes Introduction to the EFI Platform Flash AMI Bios Page Page Page Brief instruction for adding the Cdrom boot option in EFI Software Installation Page Checkpoint Code Description IA-32 Post CodesRegister for date and time next Monochrome mode and color mode settings next 47h 60h 95h Checkpoints Code Description Common Debug CodesSuper i2DMR-8G2/i2DMR-iG2 User’s Manual