SUPER MICRO Computer I2DMR-8G2 user manual Front Control Panel U66, Speaker Connector CN4

Page 32

SUPER i2DMR-8G2/i2DMR-iG2 User's Manual

Front Control Panel (U66)

U66 contains header pins for various buttons and indicators that are nor- mally located on a control panel at the front of the chassis. These connec- tors are designed specifically for use with Supermicro server chassis. See the figure below for the descriptions of the various control panel buttons and LED indicators. Refer to the following section for descriptions and pin definitions.

Figure 2-4: Front Control Panel-U66 Header Pins

20 19

Ground

 

X

 

Power LED

 

HDD LED

 

NIC1 LED

 

NIC2 LED

 

Overheat LED

 

Power Fail LED

 

Ground

 

Ground

 

2

1

NMI

X

Vcc

Vcc

Vcc

X

Vcc

Vcc

Reset Reset Button Pwr Power Button

Speaker Connector (CN4)

CN4 contains header pins for the Speaker Header located at the front of the chassis. (*See the Connector Section for details.)

Figure 2-5: CN4 Header Pins

4

3

2

Speaker

1

2-12

Image 32
Contents Super Page About This Manual Manual OrganizationTable of Contents Troubleshooting Table of ContentsBios AppendicesChecklist OverviewContacting Supermicro HeadquartersEurope Asia-PacificSuper i2DMR-8G2/i2DMR-iG2 Image Super i2DMR-8G2/i2DMR-iG2 Motherboard Layout Quick Reference i2DMR-8G2/i2DMR-iG2 Jumper Description Default SettingConnector Description Motherboard Features ChipsetM o r y Expansion SlotsAcpi Features PC Health MonitoringThermal Control Onboard I/ODimensions OtherBlock Diagram of the i2DMR-8G2/i2DMR-iG2 Motherboard Chipset Overview Major bus groups areComplementary Components include Special FeaturesPC Health Monitoring Acpi Features Power SupplyAuto-Switching Voltage Regulator for the CPU Core CPU Overheat LED and ControlSuper I/O Page Unpacking PrecautionsStatic-Sensitive Devices Itanium2 Processor and Heatsink Installation Locating the components included in the shipping packageInstallation Installing Motherboard into chassis Installation Installing and securing the Power Pod onto the Itanium Edge Connector Signal PinsPage Installing the Heatsink on the CPU*for CPU w/o Heatsink only Connecting AC Power to the motherboard and the Power Pods Memory Support Installing DIMMsDimm Installation I/OPorts/Control Panel Connectors I/O Port Locations and DefinitionsSpeaker Connector CN4 Front Control Panel U66Connecting Cables HDD LED Overheat LED OHUniversal Serial Bus USB0/1, USB2/3 Reset ButtonPower Button Front Panel Universal Serial Bus Header Serial PortsGlan Ports Ethernet Chassis IntrusionWake-On-Ring Fan HeadersSpeaker Header Connector Power FaultAlarm Reset SMB Power I2 CJumper Settings Glan Enable/DisableExplanation Jumpers Cmos ClearVGA Enable/Disable Scsi Enable/Disable *i2DMR-8G2 onlyScsi Termination Enable/ Disable *i2DMR-8G2 only Watch DogGlan LEDs Onboard IndicatorsForce-Power-On Enable Disable COM Port 1 J5 & COM Header J38 IDE ConnectorsCOM Port, IDE, Ipmi and Scsi Connections Ultra 320 Scsi Connectors *i2DMR-8G2 only IpmiPage No Power Troubleshooting ProceduresBefore Power On No Video Losing the System’s Setup ConfigurationMemory Errors Technical Support Procedures Frequently Asked QuestionsReturning Merchandise for Service Amibios IntroductionMain Setup Language MenuBSP Information System Time/System DateSetup Warning Advanced Bios SetupSuper IO Configuration Sub Menu IDE Configurations Sub Menu Serial Port1 Address/Serial Port2 AddressBlock Multi-Sector Transfer LBA/Large ModeType DMA Mode A.R.T. For Hard disk drives32Bit Data Transfer Armd Emulation TypeBios Settings Configuration Quiet BootAtapi Detect Time Out Atapi 80Pin Cable DetectionSystem Health Monitor Advanced System HealthPeripheral Device Configuration Power Loss ControlWatch Dog Timer Watch Dog Timer ValueLegacy USB Support UBS ConfigurationUSB Function PCI/PnP Configuration PCI Latency TimerAllocate IRQ to PCI VGA PCI IDE BusMasterSecurity Settings Load Optimal Defaults Load Fail-Safe DefaultsExit Options Exit Saving ChangesDiscarding Changes Introduction to the EFI Platform Flash AMI Bios Page Page Page Brief instruction for adding the Cdrom boot option in EFI Software Installation Page IA-32 Post Codes Checkpoint Code DescriptionRegister for date and time next Monochrome mode and color mode settings next 47h 60h 95h Common Debug Codes Checkpoints Code DescriptionSuper i2DMR-8G2/i2DMR-iG2 User’s Manual