SUPER MICRO Computer I2DMR-8G2 user manual Motherboard Features, Chipset, M o r y, Expansion Slots

Page 12

SUPER i2DMR-8G2/i2DMR-iG2 User's Manual

Motherboard Features

CPU

Two Intel Itanium 2 Processor sockets and power pod sites support: Single or dual Intel® Itanium 2TM processors at a 400 MHz front side bus (system) speed up to 1.5 GHz, 6MB L3 Cache. (*Notes: Please refer to

the support section of our web site for a complete listing of supported processors (http://

www.supermicro.com/TECHSUPPORT/TechSupport.htm)

Chipset

Intel E8870 chipset

SNC-M(Scalable Node Controller) of the E8870 chipset

SIOH (Server I/O Hub) of the E8870 chipset

Four Memory Repeater Hubs-DDR(MRH-D) components of the E8870 chipset

One P64H2 PCI-X bridge component

Network Interface Controller (NIC) 10/100/1000 Ethernet controller that provides two GLAN ports

One I/O Control Hub 4 (ICH 4) component:

-6 USB ports (4 at the rear, 2 headers),

-2 IDE bus routed through the flex cable to the peripheral board supporting one ATA100 master device

6-MB Flash using 6 Firmware Hub (FWH) components

M e m o r y

Eight 184-pin DIMM sockets supporting up to 16 GB Registered ECC DDR-200 (PC1600) SDRAM (utilizing DDR266 operating at 200 MHz)

Note: 4-way Interleaved memory; requires at least 4 pieces of identical memory modules to be

installed at the same time. See Section 2-3 for details.

Expansion Slots

*For 1U Server:

One 64-bit PCI-X 100 slot(*For i2DMR-8G2), One 64-bit PCI-X 133 slot (*For i2DMR-iG2)

*For 2U servers: it can support up to 3 PCI-X slots:

One 64-bit PCI-X 100 slot(*For i2DMR-8G2), One 64-bit PCI-X 133 slot (*For i2DMR-iG2)

Two 64-bit PCI-X 133 slots

1-6

Image 12
Contents Super Page About This Manual Manual OrganizationTable of Contents Troubleshooting Table of ContentsBios AppendicesChecklist OverviewContacting Supermicro HeadquartersEurope Asia-PacificSuper i2DMR-8G2/i2DMR-iG2 Image Super i2DMR-8G2/i2DMR-iG2 Motherboard Layout Jumper Description Default Setting Connector DescriptionQuick Reference i2DMR-8G2/i2DMR-iG2 Motherboard Features ChipsetM o r y Expansion SlotsAcpi Features PC Health MonitoringThermal Control Onboard I/ODimensions OtherBlock Diagram of the i2DMR-8G2/i2DMR-iG2 Motherboard Chipset Overview Major bus groups areSpecial Features PC Health MonitoringComplementary Components include Acpi Features Power SupplyAuto-Switching Voltage Regulator for the CPU Core CPU Overheat LED and ControlSuper I/O Page Precautions Static-Sensitive DevicesUnpacking Itanium2 Processor and Heatsink Installation Locating the components included in the shipping packageInstallation Installing Motherboard into chassis Installation Installing and securing the Power Pod onto the Itanium Edge Connector Signal PinsPage Installing the Heatsink on the CPU*for CPU w/o Heatsink only Connecting AC Power to the motherboard and the Power Pods Installing DIMMs Dimm InstallationMemory Support I/OPorts/Control Panel Connectors I/O Port Locations and DefinitionsSpeaker Connector CN4 Front Control Panel U66Connecting Cables HDD LED Overheat LED OHReset Button Power ButtonUniversal Serial Bus USB0/1, USB2/3 Front Panel Universal Serial Bus Header Serial PortsGlan Ports Ethernet Chassis IntrusionFan Headers Speaker HeaderWake-On-Ring Connector Power FaultAlarm Reset SMB Power I2 CJumper Settings Glan Enable/DisableExplanation Jumpers Cmos ClearVGA Enable/Disable Scsi Enable/Disable *i2DMR-8G2 onlyScsi Termination Enable/ Disable *i2DMR-8G2 only Watch DogOnboard Indicators Force-Power-On Enable DisableGlan LEDs IDE Connectors COM Port, IDE, Ipmi and Scsi ConnectionsCOM Port 1 J5 & COM Header J38 Ultra 320 Scsi Connectors *i2DMR-8G2 only IpmiPage Troubleshooting Procedures Before Power OnNo Power Losing the System’s Setup Configuration Memory ErrorsNo Video Technical Support Procedures Frequently Asked QuestionsReturning Merchandise for Service Amibios IntroductionMain Setup Language MenuBSP Information System Time/System DateAdvanced Bios Setup Super IO Configuration Sub MenuSetup Warning IDE Configurations Sub Menu Serial Port1 Address/Serial Port2 AddressLBA/Large Mode TypeBlock Multi-Sector Transfer DMA Mode A.R.T. For Hard disk drives32Bit Data Transfer Armd Emulation TypeBios Settings Configuration Quiet BootAtapi Detect Time Out Atapi 80Pin Cable DetectionSystem Health Monitor Advanced System HealthPeripheral Device Configuration Power Loss ControlWatch Dog Timer Watch Dog Timer ValueUBS Configuration USB FunctionLegacy USB Support PCI/PnP Configuration PCI Latency TimerAllocate IRQ to PCI VGA PCI IDE BusMasterSecurity Settings Load Optimal Defaults Load Fail-Safe DefaultsExit Options Exit Saving ChangesDiscarding Changes Introduction to the EFI Platform Flash AMI Bios Page Page Page Brief instruction for adding the Cdrom boot option in EFI Software Installation Page IA-32 Post Codes Checkpoint Code DescriptionRegister for date and time next Monochrome mode and color mode settings next 47h 60h 95h Common Debug Codes Checkpoints Code DescriptionSuper i2DMR-8G2/i2DMR-iG2 User’s Manual