SUPER MICRO Computer I2DMR-8G2 user manual Installing Motherboard into chassis

Page 24

SUPER i2DMR-8G2/i2DMR-iG2 User's Manual

C. Installing Motherboard into chassis

*Note: To optimize the functionality and the capability of the i2DMR-8G2/i2DMR-iG2, we strongly recommend that the i2DMR-8G2/i2DMR-iG2 be installed in Supermicro's proprietary chassis only-theSC813HS-500W (*for 1 U), SC823HS-500W (*for 2U).

1.Locate six(6) 6-32 8mm screws in the retention mechanism shipping package.

2.On the retention mechanism located on the motherboard, locate the six

mounting holes (as shown in the picture below), and locate their six corresponding mounting holes in the chassis.

3.Align the six mounting holes on the motherboard against the corre- sponding mounting holes in the chassis.

4.Screw six (6) 6-32 8mm screws into the mounting holes on the retention mechanism and the mounting holes in the chassis as shown in the pictures below.

5.Locate six 6-32 4.5mm screws included in the chassis mounting kit. Secure the motherboard onto the chassis by screwing 6-32 4.5mm screws into all the remaining mounting holes on the motherboard and the mounting holes in the chassis.

1.) Screw six 6-32 8mm screws into mounting holes on the board and on the

chassis.

2.) Secure the motherboard onto the chassis by screwing 6-32 4.5mm screws into all the remaining mounting holes on the board and on the chassis.

2-4

Image 24
Contents Super Page About This Manual Manual OrganizationTable of Contents Troubleshooting Table of ContentsBios AppendicesChecklist OverviewContacting Supermicro HeadquartersEurope Asia-PacificSuper i2DMR-8G2/i2DMR-iG2 Image Super i2DMR-8G2/i2DMR-iG2 Motherboard Layout Jumper Description Default Setting Connector DescriptionQuick Reference i2DMR-8G2/i2DMR-iG2 Motherboard Features ChipsetM o r y Expansion SlotsAcpi Features PC Health MonitoringThermal Control Onboard I/ODimensions OtherBlock Diagram of the i2DMR-8G2/i2DMR-iG2 Motherboard Chipset Overview Major bus groups areSpecial Features PC Health MonitoringComplementary Components include Acpi Features Power SupplyAuto-Switching Voltage Regulator for the CPU Core CPU Overheat LED and ControlSuper I/O Page Precautions Static-Sensitive DevicesUnpacking Itanium2 Processor and Heatsink Installation Locating the components included in the shipping packageInstallation Installing Motherboard into chassis Installation Installing and securing the Power Pod onto the Itanium Edge Connector Signal PinsPage Installing the Heatsink on the CPU*for CPU w/o Heatsink only Connecting AC Power to the motherboard and the Power Pods Installing DIMMs Dimm InstallationMemory Support I/OPorts/Control Panel Connectors I/O Port Locations and DefinitionsSpeaker Connector CN4 Front Control Panel U66Connecting Cables HDD LED Overheat LED OHReset Button Power ButtonUniversal Serial Bus USB0/1, USB2/3 Front Panel Universal Serial Bus Header Serial PortsGlan Ports Ethernet Chassis IntrusionFan Headers Speaker HeaderWake-On-Ring Connector Power FaultAlarm Reset SMB Power I2 CJumper Settings Glan Enable/DisableExplanation Jumpers Cmos ClearVGA Enable/Disable Scsi Enable/Disable *i2DMR-8G2 onlyScsi Termination Enable/ Disable *i2DMR-8G2 only Watch DogOnboard Indicators Force-Power-On Enable DisableGlan LEDs IDE Connectors COM Port, IDE, Ipmi and Scsi ConnectionsCOM Port 1 J5 & COM Header J38 Ultra 320 Scsi Connectors *i2DMR-8G2 only IpmiPage Troubleshooting Procedures Before Power OnNo Power Losing the System’s Setup Configuration Memory ErrorsNo Video Technical Support Procedures Frequently Asked QuestionsReturning Merchandise for Service Amibios IntroductionMain Setup Language MenuBSP Information System Time/System DateAdvanced Bios Setup Super IO Configuration Sub MenuSetup Warning IDE Configurations Sub Menu Serial Port1 Address/Serial Port2 AddressLBA/Large Mode TypeBlock Multi-Sector Transfer DMA Mode A.R.T. For Hard disk drives32Bit Data Transfer Armd Emulation TypeBios Settings Configuration Quiet BootAtapi Detect Time Out Atapi 80Pin Cable DetectionSystem Health Monitor Advanced System HealthPeripheral Device Configuration Power Loss ControlWatch Dog Timer Watch Dog Timer ValueUBS Configuration USB FunctionLegacy USB Support PCI/PnP Configuration PCI Latency TimerAllocate IRQ to PCI VGA PCI IDE BusMasterSecurity Settings Load Optimal Defaults Load Fail-Safe DefaultsExit Options Exit Saving ChangesDiscarding Changes Introduction to the EFI Platform Flash AMI Bios Page Page Page Brief instruction for adding the Cdrom boot option in EFI Software Installation Page IA-32 Post Codes Checkpoint Code DescriptionRegister for date and time next Monochrome mode and color mode settings next 47h 60h 95h Common Debug Codes Checkpoints Code DescriptionSuper i2DMR-8G2/i2DMR-iG2 User’s Manual