SUPER MICRO Computer I2DMR-8G2 user manual Common Debug Codes, Checkpoints Code Description

Page 77

Appendix A: BIOS POST Checkpoint Codes

A-2 Common Debug Codes

Common Debug Codes for the motherboard are listed below:

Checkpoints

 

Code Description

DS4

DS3

 

On

On:

SNC found and start memory sizing

On

Off:

Initial system memory and SIOH

Off

On:

Valid memory and SIOH found

Off

Off:

ICH4 found

A-7

Page 76 Page 78
Image 77
Page 76 Page 78
Contents Super Page Manual Organization About This ManualTable of Contents Table of Contents TroubleshootingAppendices BiosOverview ChecklistHeadquarters Contacting SupermicroEurope Asia-PacificSuper i2DMR-8G2/i2DMR-iG2 Image Super i2DMR-8G2/i2DMR-iG2 Motherboard Layout Quick Reference i2DMR-8G2/i2DMR-iG2 Jumper Description Default SettingConnector Description Chipset Motherboard FeaturesM o r y Expansion SlotsPC Health Monitoring Acpi FeaturesThermal Control Onboard I/OOther DimensionsBlock Diagram of the i2DMR-8G2/i2DMR-iG2 Motherboard Major bus groups are Chipset OverviewComplementary Components include Special FeaturesPC Health Monitoring Power Supply Acpi FeaturesAuto-Switching Voltage Regulator for the CPU Core CPU Overheat LED and ControlSuper I/O Page Unpacking PrecautionsStatic-Sensitive Devices Locating the components included in the shipping package Itanium2 Processor and Heatsink InstallationInstallation Installing Motherboard into chassis Installation Edge Connector Signal Pins Installing and securing the Power Pod onto the ItaniumPage Installing the Heatsink on the CPU*for CPU w/o Heatsink only Connecting AC Power to the motherboard and the Power Pods Memory Support Installing DIMMsDimm Installation I/O Port Locations and Definitions I/OPorts/Control Panel ConnectorsFront Control Panel U66 Speaker Connector CN4Connecting Cables Overheat LED OH HDD LEDUniversal Serial Bus USB0/1, USB2/3 Reset ButtonPower Button Serial Ports Front Panel Universal Serial Bus HeaderGlan Ports Ethernet Chassis IntrusionWake-On-Ring Fan HeadersSpeaker Header Power Fault ConnectorAlarm Reset SMB Power I2 CGlan Enable/Disable Jumper SettingsExplanation Jumpers Cmos ClearScsi Enable/Disable *i2DMR-8G2 only VGA Enable/DisableScsi Termination Enable/ Disable *i2DMR-8G2 only Watch DogGlan LEDs Onboard IndicatorsForce-Power-On Enable Disable COM Port 1 J5 & COM Header J38 IDE ConnectorsCOM Port, IDE, Ipmi and Scsi Connections Ipmi Ultra 320 Scsi Connectors *i2DMR-8G2 onlyPage No Power Troubleshooting ProceduresBefore Power On No Video Losing the System’s Setup ConfigurationMemory Errors Frequently Asked Questions Technical Support ProceduresReturning Merchandise for Service Introduction AmibiosLanguage Menu Main SetupBSP Information System Time/System DateSetup Warning Advanced Bios SetupSuper IO Configuration Sub Menu Serial Port1 Address/Serial Port2 Address IDE Configurations Sub MenuBlock Multi-Sector Transfer LBA/Large ModeType A.R.T. For Hard disk drives DMA Mode32Bit Data Transfer Armd Emulation TypeQuiet Boot Bios Settings ConfigurationAtapi Detect Time Out Atapi 80Pin Cable DetectionAdvanced System Health System Health MonitorPower Loss Control Peripheral Device ConfigurationWatch Dog Timer Watch Dog Timer ValueLegacy USB Support UBS ConfigurationUSB Function PCI Latency Timer PCI/PnP ConfigurationAllocate IRQ to PCI VGA PCI IDE BusMasterSecurity Settings Load Fail-Safe Defaults Load Optimal DefaultsExit Options Exit Saving ChangesDiscarding Changes Introduction to the EFI Platform Flash AMI Bios Page Page Page Brief instruction for adding the Cdrom boot option in EFI Software Installation Page Checkpoint Code Description IA-32 Post CodesRegister for date and time next Monochrome mode and color mode settings next 47h 60h 95h Checkpoints Code Description Common Debug CodesSuper i2DMR-8G2/i2DMR-iG2 User’s Manual
Top Page Image Contents