Sierra 240-VTP, 241-VTP instruction manual Appendix a Product Specifications

Series 24-HP Instruction ManualAppendix A Specifications

Appendix A Product Specifications

Accuracy
Process		240 Series In-Line Meters		241 Series Insertion Meters		(1)
Variables
		Liquids	Gas & Steam	Liquids	Gas &
					Steam
Mass Flow		±1% of rate	±1.5% of	±1.5% of rate	±2% of
Rate		over a 30:1	rate(2) over a	over a 30:1	rate(2) over
		range(3)	30:1 range(3)	range(3)	a 30:1
					range(3)
Volumetric		±0.7% of	±1% of rate	±1.2% of rate	±1.5% of
Flow Rate		rate over a	over a 30:1	over a 30:1	rate over a
		30:1	range(3)	range(3)	30:1
		range(3)			range(3)
Temperature		± 2°F	± 2°F	± 2°F	± 2°F
		(± 1°C)	(± 1°C)	(± 1°C)	(± 1°C)
Pressure		0.4% of	0.4% of	0.4% of	0.4% of
		transducer	transducer	transducer full	transducer
		full scale	full scale	scale	full scale
Density		0.3% of	0.5% of	0.3% of	0.5% of
		reading	reading(2)	reading	reading(2)
Notes:	(1) Accuracies stated are for the total mass flow through the pipe.

(2)Over 50 to 100% of the pressure transducer’s full scale.

(3)Nominal rangeability is stated. Precise rangeability depends on fluid and pipe size.

	Repeatability				Mass Flow Rate: 0.2% of rate.
					Volumetric Flow Rate: 0.1% of rate.
					Temperature:		± 0.2°F (± 0.1°C).
					Pressure: 0.05% of full scale.
					Density: 0.1% of reading.
	Stability Over 12 Months				Mass Flow Rate: 0.2% of rate maximum.
					Volumetric Flow Rate: Negligible error.
					Temperature: ± 0.1°F (± 0.5°C) maximum.
					Pressure: 0.1% of full scale maximum.
					Density: 0.1% of reading maximum.
	Response Time				Adjustable from 1 to 100 seconds.
	Material Capability				Series 240 In-Line Flow Meter:
					Any gas, liquid or steam compatible with 316L stainless steel, C276
					hastelloy or A105 carbon steel. Not recommended for multi-phase
					fluids.
					Series 241 Insertion Flow Meter:
					Any gas, liquid or steam compatible with 316L stainless steel. Not
					recommended for multi-phase fluids.
	Flow Rates				Typical mass flow ranges are given in the following table. Precise
					flow depends on the fluid and pipe size. 241 insertion meters are
					applicable to pipe sizes from 2 inch and above. Consult factory for
					sizing program.
			Water Minimum and Maximum Flow Rates
	½-inch	¾-inch		1-inch		1.5-inch	2-inch	3-inch	4-inch	6-inch	8-inch
gpm	1	1.3		2.2		5.5	9.2	21	36	81	142
	22	40		67		166	276	618	1076	2437	4270
m3/hr	.23	.3		0.5		1.3	2.1	4.7	8.1	18	32
	5	9.1		15		38	63	140	244	554	970

IM-24-HP A-1