SMC Networks user manual Hardware Setup, MBP Card Setup Connecting Power to the 1560-MBP Card

Page 10

Chapter 3 — Hardware Setup

Contents

3 Hardware Setup

3.11560-MBP Card Setup

3.1.1 Connecting Power to the 1560-MBP Card

Connecting power requires a simple termination of the 120 VAC or 24 VDC cable to the front of the module. The connections are shown in the following diagram:

115 VAC Hot		L	24 VDC +		+

115 VAC Neutral		N	24 VDC Common		Com

Ground		G	Ground		G

3.1.2 Dip Switch Configuration

Configuration of the 1560-MBP consists of setting up some dip switches. The dip switches are as follows:

Host & Slave Address

Add values of switches and then add 1 to total

to calculate address

			SW					Value				Examples
			SW					Value				Address 1
			1				1					Address 1
			2				2					6					5 4		3		2 1
			3				4					ON
			4				8					OFF
			5				16					(0+0+0+0+0+0)=0+1=1
			6				32					(0+0+0+0+0+0)=0+1=1
			6				32					Address 8


												6					5 4 3				2	1
		HOST					SLAVE					ON
		HOST					SLAVE					OFF
												(0+0+0+4+2+1)=7+1=8
												(0+0+0+4+2+1)=7+1=8


Datalinks
8 7		8 7				8 7	8 7
8 7		8 7				8 7	8 7

Fault on Loss of Modbus Plus

8 8

ON=Enable

OFF=Disable

Global Database

Control

7 7

ON=Enable

OFF=Disable

											ON
											OFF
A,D,C,D A&D only A only									NONE

8 7 6 5 4 3 2 1

ON

OFF

8 7 6 5 4 3 2 1

ON

OFF

Please note that dip switch configuration is read by the 1560-MBP during the power up process. Power must be cycled if dip switches are changed under power.

10

Image 10

Contents 1560 Table of Contents Please Read This Notice Quick Start Guide Step-by-StepRevisions General Specifications Product SpecificationsModbus Plus Specifications Configuration via dip switches Slave Address Host Address24 VDC Operating Temp To 50 C Storage Temp 40 to 85 C Modbus Plus Port Functionality Supported Mstr Programming CommandsModbus Plus Communications Mstr Type 5 Write Global Data Modbus Register MapMBP Modbus Address Space 1560-MBP Card Setup Connecting Power to the 1560-MBP Card Hardware SetupDip Switch Configuration Switch SW Modbus Function Description Details Fault onLoss PlusSwitch SW 2 cont’d Contents Writing to the 1560-MBP Global Data Enabled Mstr Type Programming Considerations1560-MBP Global Data Modicon Programming Example Mstr Enable 40400 ActiveAbort Error 40410 SuccessHost Issued Write Commands Mstr Type Global Data Mstr Type Reading from the 1560-MBPModicon Programming Example Mstr Type 40510 Host Issued Read Commands Mstr TypeEnable 40500 Active 0001040060 4005000020 MBP Status Registers 40021 to Modbus Name Values Description AddressBatch At this time LED Troubleshooting Table TroubleshootingLED Locations SCANport Mbpstat Diagnostics Cable Diagram TxRxD+Technical Support Technical Support ContactsMBP Modbus Register Map Appendix aMBP Modbus Appendix B Device Specific HintsLogic Control Word Bit Function Description Setting up the Adaptor I/O DataDrive Status Word Bit Function Description Single Drive Peer Cop Application Example Hardware ConfigurationAppendix C OverviewSwitch Position Description Configuration Extension BlocksPLC REF Drive Status RefOffset Description Ladder Logic ProgrammingPLC Ref PLC Name Description Special Precautions and hints TimingAddressing HintsMounting Instructions Appendix DMounting and SCANport Cabling Instructions 70mmCable Requirements Appendix E SCANport Datalink OperationService and Repair Repair and WarrantyGeneral Warranty Policy Hardware Product Warranty Details Limitation of LiabilityContents