SMC Networks 1560 user manual Limitation of Liability, Hardware Product Warranty Details

Page 43

Repair and Warranty

Limitation of Liability

EXCEPT AS EXPRESSLY PROVIDED HEREIN, PROSOFT MAKES NO WARRANT OF ANY KIND, EXPRESSED OR IMPLIED, WITH RESPECT TO ANY EQUIPMENT, PARTS OR SERVICES PROVIDED PURSUANT TO THIS AGREEMENT, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANT ABILITY AND FITNESS FOR A PARTICULAR PURPOSE. NEITHER PROSOFT OR ITS DEALER SHALL BE LIABLE FOR ANY OTHER DAMAGES, INCLUDING BUT NOT LIMITED TO DIRECT, INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES, WHETHER IN AN ACTION IN CONTRACT OR TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY), SUCH AS, BUT NOT LIMITED TO, LOSS OF ANTICIPATED PROFITS OR BENEFITS RESULTING FROM, OR ARISING OUT OF, OR IN CONNECTION WITH THE USE OR FURNISHING OF EQUIPMENT, PARTS OR SERVICES HEREUNDER OR THE PERFORMANCE, USE OR INABILITY TO USE THE SAME, EVEN IF PROSOFT OR ITS DEALER’S TOTAL LIABILITY EXCEED THE PRICE PAID FOR THE PRODUCT.

Where directed by State Law, some of the above exclusions or limitations may not be applicable in some states. This warranty provides specific legal rights; other rights that vary from state to state may also exist. This warranty shall not be applicable to the extent that any provisions of this warranty is prohibited by any Federal, State or Municipal Law that cannot be preempted.

Hardware Product Warranty Details

Warranty Period: ProSoft warranties hardware product for a period of one (1) year.

Warranty Procedure: Upon return of the hardware Product ProSoft will, at its option, repair or replace Product at no additional charge, freight prepaid, except as set forth below. Repair parts and replacement Product will be furnished on an exchange basis and will be either reconditioned or new. All replaced Product and parts become the property of ProSoft. If ProSoft determines that the Product is not under warranty, it will, at the Customer’s option, repair the Product using current ProSoft standard rates for parts and labor, and return the Product freight collect.

43

Image 43
Contents 1560 Table of Contents Please Read This Notice Step-by-Step Quick Start GuideRevisions Configuration via dip switches Slave Address Host Address Product SpecificationsModbus Plus Specifications General Specifications24 VDC Operating Temp To 50 C Storage Temp 40 to 85 C Modbus Plus Port Functionality Supported Mstr Programming CommandsModbus Plus Communications Mstr Type 5 Write Global Data Modbus Register MapMBP Modbus Address Space 1560-MBP Card Setup Connecting Power to the 1560-MBP Card Hardware SetupDip Switch Configuration Switch SW Plus Function Description Details Fault onLoss ModbusSwitch SW 2 cont’d Contents Programming Considerations Writing to the 1560-MBP Global Data Enabled Mstr Type1560-MBP Global Data Success Enable 40400 ActiveAbort Error 40410 Modicon Programming Example MstrHost Issued Write Commands Mstr Type Global Data Mstr Type Reading from the 1560-MBPModicon Programming Example Mstr Type 00010 Host Issued Read Commands Mstr TypeEnable 40500 Active 4051040060 4005000020 Modbus Name Values Description Address MBP Status Registers 40021 toBatch At this time LED Troubleshooting Table TroubleshootingLED Locations SCANport Mbpstat Diagnostics TxRxD+ Cable DiagramTechnical Support Contacts Technical SupportMBP Modbus Register Map Appendix aMBP Modbus Device Specific Hints Appendix BLogic Control Word Bit Function Description Setting up the Adaptor I/O DataDrive Status Word Bit Function Description Overview Hardware ConfigurationAppendix C Single Drive Peer Cop Application ExampleConfiguration Extension Blocks Switch Position DescriptionPLC REF Drive Status RefOffset Description Ladder Logic ProgrammingPLC Ref PLC Name Description Timing Special Precautions and hintsHints Addressing70mm Appendix DMounting and SCANport Cabling Instructions Mounting InstructionsCable Requirements SCANport Datalink Operation Appendix EService and Repair Repair and WarrantyGeneral Warranty Policy Limitation of Liability Hardware Product Warranty DetailsContents