Western Telematic CMS-16 manual Apply Power to the CMS, System SetUp Ports

Page 10

3.2. Apply Power to the CMS

Connect the CMS to an appropriate power source. Press the Power Switch ON. The ON LED should light, and the RDY LED should begin to flash. When connecting power to a DC unit, please refer to the additional instructions in Section 4.1.

CAUTION: This device should only be operated with the type of power source indicated on the instrument nameplate. If you are not sure of the type of power service available, please consult your local power company.

3.3. System SetUp Ports

In order to ensure access to important command functions, Ports 1 and 2 are designated as System SetUp Ports; the Supervisor Mode cannot be disabled at these ports. Ports 1 and 2 will always allow password protected access to all CMS command functions, even when the unit has been reset to the default state.

Therefore, Ports 1 and 2 are generally used for communication during initial set-up and configuration, or after the unit has been reinitialized (reset) to default parameters.

Note: For more information on System SetUp Port capabilities, please refer to Section 5.2.

3.4. Connecting your PC to the CMS

The CMS can either be controlled by a local PC that communicates via cable, controlled via external modem, or controlled via TCP/IP network. For this overview, a local PC running ProComm (or a similar communications program), will be cable connected to Port 1.

Note: Communication via Modem (Optional): If desired, this overview can also be performed via modem. Section 4.4 describes the procedure for connecting a modem to the CMS.

1.Attach a standard null modem cable to your PC COM port. Make certain to connect to the COM port used by your communications program.

2.Connect the other end of the cable to CMS Port 1. For a description of the port interface, please refer to Appendix A.

3.5. Communicating with the CMS Unit

Image 10

Contents CMS-16 Battery Replacement Nameplate Power WarningRack Mount Installation Table of Contents Page Appendices List of FiguresIntroduction Front Panel Unit DescriptionTypographic Conventions Power Cable Receptacle Power Switch Back PanelGetting Started Using Other Parameters for this Overview OptionalCommunication Parameters Connecting your PC to the CMS Apply Power to the CMSSystem SetUp Ports Communicating with the CMS UnitCommand Menu Display Configuration ControlPort Name Password StatusHardware Installation Connecting Power to the CMS UnitAC Powered Units Configure Option SwitchesDC Powered Units Default Baud Rate Sw1, Sw2, Sw3 Default Handshake Sw4, Sw5Default Response Message Format Sw6 Initialize Unit to Default SettingsDefault Command Echo Sw7 Connecting Devices to the CMS Application ExampleCMS Application Example Not to Scale Configuration Access to the CMS Command Mode$ telnet 192.1.1.1 Enter Password Functions Supervisor PasswordDefining the Site ID and Supervisor Password Port PasswordsPort Configuration Configuration Conventions3. RS232 Port Configuration Menus Port ModesPort Parameters #02 CTS/RTSParameters #02 Stop Bits Default =ATZ AT&C1$D2S0=1 Network Port Configuration Menu Network Parameters Telnet Port ParametersPage Implementing IP Security IP SecurityPage Copying Parameters to All Ports Copy Port ParametersSave User Selected Parameters Status ScreensPort Status Screen /S Status Mode Buffer Count Port Status Screen Supervisor Mode, Defaults ShownMode BUF CTS Port Diagnostics Screen /SDDiagnostics Name StatusNetwork Status Screen /SN Telnet Port Status Port Parameters Screens /WNetwork Status LAN Status CMSPort Parameters #03 RTS/CTSOperation Any-to-Any ModePort Connection and Disconnection Disconnecting Ports Enter Defining Hunt Groups Hunt Group ExamplePassive Mode Buffer ModeReading Data from Buffer Mode Ports Xx EnterModem Mode Port BuffersSending Parameters to a File Saving and Restoring Configuration ParametersRestoring Saved Parameters Upgrading CMS Firmware Command Reference Guide Command ConventionsCommand Response Command Summary Terse VerboseWP n Enter Enter+++Enter Resident Disconnect Sequence Command SetEnter Enter Command Mode ConnectFormat /CP Enter Format /C x x EnterCP Copy RS232 Port Parameters Third Party DisconnectErase Buffer Format /D/Y x x Enter2 Enter or /D/Y 3 Enter Format /E/Y x x EnterHelp Default and TestDisplay Site ID Set RS232 Port Parameters Set Network Port ParametersDisplay Port Status SN Display Network Status SD Display Port DiagnosticsReset Network Port Save ParametersFormat /UF Enter UF Upgrade FirmwareExit Command Mode Display Port Parameters WhoAppendix A. RS232 Port Interface Appendix B. SpecificationsFormat /X Enter Power Appendix C. Customer ServiceStop Bits 1 or Trademark and Copyright Information Trademarks Used in this Manual

Related manuals

Manual 59 pages 31.71 Kb