Western Telematic CMS-16 manual Hardware Installation, Connecting Power to the CMS Unit

Page 13

create a connection between two other ports.

i.To connect Port 2 to Port 3, type /C 2 3 [Enter].

ii.While Ports 2 and 3 are connected, Port 1 will still recognize CMS commands. Type /S [Enter] to display the Port Status Screen. The "STATUS" column should now list Ports 2 and 3 as connected, and Port 1 as "Free".

iii.Issue a Third Party Disconnect command to disconnect Ports 2 and 3; type /D 2 [Enter]. The unit will display the "Are you Sure (y/n)?" prompt. Type y and press [Enter] to disconnect.

iv.Type /S [Enter] to display the Port Status Screen. The "STATUS" column should now list Ports 2 and 3 as "Free".

7.Site I.D. Message: If desired, the Site I.D. Message can be used to indicate the name or location of the unit. Note that the Site I.D. cannot include double quotes (").

. Type /F and press [Enter]. When the System Parameters menu appears, type 1 and press [Enter]. A prompt will appear. Key in the desired text (up to 32 characters) and press [Enter].

b.To display the Site I.D., type /J [Enter].

c.Note that the Site I.D. will be cleared when the unit is initialized.

This completes the introductory overview of the CMS. Please proceed to Section 4 and Section 5 for complete installation and configuration procedures.

4. Hardware Installation

4.1. Connecting Power to the CMS Unit

The CMS is available in both AC and DC powered versions. When connecting AC or DC power to the CMS, proceed as follows:

Image 13

Contents CMS-16 Battery Replacement Nameplate Power WarningRack Mount Installation Table of Contents Page List of Figures AppendicesIntroduction Front Panel Unit DescriptionTypographic Conventions Back Panel Power Cable Receptacle Power SwitchGetting Started Using Other Parameters for this Overview OptionalCommunication Parameters System SetUp Ports Apply Power to the CMSConnecting your PC to the CMS Communicating with the CMS UnitControl Command Menu Display ConfigurationStatus Port Name PasswordConnecting Power to the CMS Unit Hardware InstallationAC Powered Units Configure Option SwitchesDC Powered Units Default Handshake Sw4, Sw5 Default Baud Rate Sw1, Sw2, Sw3Default Response Message Format Sw6 Initialize Unit to Default SettingsDefault Command Echo Sw7 Application Example Connecting Devices to the CMSCMS Application Example Not to Scale Access to the CMS Command Mode Configuration$ telnet 192.1.1.1 Enter Supervisor Password Password FunctionsPort Passwords Defining the Site ID and Supervisor PasswordConfiguration Conventions Port ConfigurationPort Modes 3. RS232 Port Configuration MenusCTS/RTS Port Parameters #02Parameters #02 Stop Bits Default =ATZ AT&C1$D2S0=1 Network Port Configuration Menu Telnet Port Parameters Network ParametersPage IP Security Implementing IP SecurityPage Copy Port Parameters Copying Parameters to All PortsSave User Selected Parameters Status ScreensPort Status Screen /S Port Status Screen Supervisor Mode, Defaults Shown Status Mode Buffer CountDiagnostics Port Diagnostics Screen /SDMode BUF CTS Name StatusNetwork Status Screen /SN Network Status LAN Status Port Parameters Screens /WTelnet Port Status CMSRTS/CTS Port Parameters #03Operation Any-to-Any ModePort Connection and Disconnection Disconnecting Ports Enter Hunt Group Example Defining Hunt GroupsBuffer Mode Passive ModeXx Enter Reading Data from Buffer Mode PortsPort Buffers Modem ModeSending Parameters to a File Saving and Restoring Configuration ParametersRestoring Saved Parameters Upgrading CMS Firmware Command Conventions Command Reference GuideCommand Response Terse Verbose Command SummaryWP n Enter Enter Enter Command Mode Command SetEnter+++Enter Resident Disconnect Sequence ConnectCP Copy RS232 Port Parameters Format /C x x EnterFormat /CP Enter Third Party Disconnect2 Enter or /D/Y 3 Enter Format /D/Y x x EnterErase Buffer Format /E/Y x x EnterHelp Default and TestDisplay Site ID Set RS232 Port Parameters Set Network Port ParametersDisplay Port Status Reset Network Port SD Display Port DiagnosticsSN Display Network Status Save ParametersExit Command Mode UF Upgrade FirmwareFormat /UF Enter Display Port Parameters WhoAppendix A. RS232 Port Interface Appendix B. SpecificationsFormat /X Enter Power Appendix C. Customer ServiceStop Bits 1 or Trademarks Used in this Manual Trademark and Copyright Information

Related manuals

Manual 59 pages 31.71 Kb