Western Telematic CMS-16 SD Display Port Diagnostics, SN Display Network Status, Save Parameters

Page 58

/SD Display Port Diagnostics

Provides more detailed information regarding the operational status of each port. Note that in User Mode, this screen will only display parameters for the ports that are allowed by the Port Password that was entered at log in. For More information on the Port Diagnostics Screen, please refer to Section 6.2.

Availability: Supervisor / User

Format: /SD [Enter]

Response: Displays Port Diagnostics Screen

/SN Display Network Status

Displays the Network Status Screen, which lists current conditions and parameters for the Network Port. For more information on the Network Status Screen, please refer to Section 6.3.

Availability: Supervisor Only

Format: /SN [Enter]

Response: Displays Network Status Screen

/T Reset Network Port

Resets the NIC card, and breaks the network connection to the unit. Note that when this command is invoked, the network connection will be reset without warning, and must then be re-established in order to communicate with the unit via Network.

Availability: Supervisor Only

Format: /T [Enter]

Response: None (NIC Card is reset, Network Connection is broken)

/U Save Parameters

Sends CMS configuration parameters to an ASCII text file as described in Section 8.

Availability: Supervisor Only

Format: /U [Enter]

Response: The CMS will send a series of command lines.

Image 58

Contents CMS-16 Battery Replacement Nameplate Power WarningRack Mount Installation Table of Contents Page Appendices List of FiguresIntroduction Front Panel Unit DescriptionTypographic Conventions Power Cable Receptacle Power Switch Back PanelGetting Started Using Other Parameters for this Overview OptionalCommunication Parameters Connecting your PC to the CMS Apply Power to the CMSSystem SetUp Ports Communicating with the CMS UnitCommand Menu Display Configuration ControlPort Name Password StatusHardware Installation Connecting Power to the CMS UnitAC Powered Units Configure Option SwitchesDC Powered Units Default Baud Rate Sw1, Sw2, Sw3 Default Handshake Sw4, Sw5Default Response Message Format Sw6 Initialize Unit to Default SettingsDefault Command Echo Sw7 Connecting Devices to the CMS Application ExampleCMS Application Example Not to Scale Configuration Access to the CMS Command Mode$ telnet 192.1.1.1 Enter Password Functions Supervisor PasswordDefining the Site ID and Supervisor Password Port PasswordsPort Configuration Configuration Conventions3. RS232 Port Configuration Menus Port ModesPort Parameters #02 CTS/RTSParameters #02 Stop Bits Default =ATZ AT&C1$D2S0=1 Network Port Configuration Menu Network Parameters Telnet Port ParametersPage Implementing IP Security IP SecurityPage Copying Parameters to All Ports Copy Port ParametersSave User Selected Parameters Status ScreensPort Status Screen /S Status Mode Buffer Count Port Status Screen Supervisor Mode, Defaults ShownMode BUF CTS Port Diagnostics Screen /SDDiagnostics Name StatusNetwork Status Screen /SN Telnet Port Status Port Parameters Screens /WNetwork Status LAN Status CMSPort Parameters #03 RTS/CTSOperation Any-to-Any ModePort Connection and Disconnection Disconnecting Ports Enter Defining Hunt Groups Hunt Group ExamplePassive Mode Buffer ModeReading Data from Buffer Mode Ports Xx EnterModem Mode Port BuffersSending Parameters to a File Saving and Restoring Configuration ParametersRestoring Saved Parameters Upgrading CMS Firmware Command Reference Guide Command ConventionsCommand Response Command Summary Terse VerboseWP n Enter Enter+++Enter Resident Disconnect Sequence Command SetEnter Enter Command Mode ConnectFormat /CP Enter Format /C x x EnterCP Copy RS232 Port Parameters Third Party DisconnectErase Buffer Format /D/Y x x Enter2 Enter or /D/Y 3 Enter Format /E/Y x x EnterHelp Default and TestDisplay Site ID Set RS232 Port Parameters Set Network Port ParametersDisplay Port Status SN Display Network Status SD Display Port DiagnosticsReset Network Port Save ParametersFormat /UF Enter UF Upgrade FirmwareExit Command Mode Display Port Parameters WhoAppendix A. RS232 Port Interface Appendix B. SpecificationsFormat /X Enter Power Appendix C. Customer ServiceStop Bits 1 or Trademark and Copyright Information Trademarks Used in this Manual

Related manuals

Manual 59 pages 31.71 Kb