Western Telematic CMS-16 manual Port Parameters #02, Cts/Rts

Page 25

Parameters selected via these menus will stay in effect until the unit is initialized or the /P command is used to reconfigure the port. After initialization, parameters will revert to the defaults specified by the Option Switches.

To select port parameters, proceed as follows:

1.Access the Command Mode. If the password prompt is displayed, key in your Supervisor Level Password.

2.Type /P, followed by the number of the port to be configured, and press [Enter]. For example, to configure Port 2, type /P 2 [Enter]. The Port Configuration menu will appear (Figure 5.1).

. If the /P Command is entered without the port number (e.g. /P [Enter]), the configuration menu for your resident port will be displayed.

b. The /P command is only available in the Supervisor Mode

PORT PARAMETERS #02

1.

Port Name:

(undefined)

2.

Password:

(undefined)

3.

Baud Rate:

9600

4.

Bits/Parity:

8-None

5.

Stop Bits:

1

6.

Handshake Mode:

CTS/RTS

7.

Port Mode:

Any-to-Any

 

74. DTR Output:

Pulse

8.

Supervisor Mode:

Permit

9.

Logoff Character:

+

10.Sequence Disconnect: Three Characters

11.Timeout Disconnect: Off

12.

Response Type:

Verbose

13.

Command Echo:

On

14.

Accept Break:

Yes

Enter: "<" Previous Port,

">" Next Port,

<ESC> Exit ...

Figure 5.1: Port Configuration Menu (Port 2 Shown)

The Port Configuration menu offers the following options:

1. Port Name: (Up to 16 characters) Assigns a name to the port. (Default = undefined).

2. Password: (Up to 16 characters) Defines the Port Password for this port. Note that identical Port Passwords are generally assigned to several ports. When this password is entered at the login prompt, the user will then have access to all ports that share this password. (Default = undefined).

Image 25
Contents CMS-16 Battery Replacement Nameplate Power WarningRack Mount Installation Table of Contents Page List of Figures AppendicesIntroduction Front Panel Unit DescriptionTypographic Conventions Back Panel Power Cable Receptacle Power SwitchGetting Started Using Other Parameters for this Overview OptionalCommunication Parameters System SetUp Ports Apply Power to the CMSConnecting your PC to the CMS Communicating with the CMS UnitControl Command Menu Display ConfigurationStatus Port Name PasswordConnecting Power to the CMS Unit Hardware InstallationAC Powered Units Configure Option SwitchesDC Powered Units Default Handshake Sw4, Sw5 Default Baud Rate Sw1, Sw2, Sw3Default Response Message Format Sw6 Initialize Unit to Default SettingsDefault Command Echo Sw7 Application Example Connecting Devices to the CMSCMS Application Example Not to Scale Access to the CMS Command Mode Configuration$ telnet 192.1.1.1 Enter Supervisor Password Password FunctionsPort Passwords Defining the Site ID and Supervisor PasswordConfiguration Conventions Port ConfigurationPort Modes 3. RS232 Port Configuration MenusCTS/RTS Port Parameters #02Parameters #02 Stop Bits Default =ATZ AT&C1$D2S0=1 Network Port Configuration Menu Telnet Port Parameters Network ParametersPage IP Security Implementing IP SecurityPage Copy Port Parameters Copying Parameters to All PortsSave User Selected Parameters Status ScreensPort Status Screen /S Port Status Screen Supervisor Mode, Defaults Shown Status Mode Buffer CountDiagnostics Port Diagnostics Screen /SDMode BUF CTS Name StatusNetwork Status Screen /SN Network Status LAN Status Port Parameters Screens /WTelnet Port Status CMSRTS/CTS Port Parameters #03Operation Any-to-Any ModePort Connection and Disconnection Disconnecting Ports Enter Hunt Group Example Defining Hunt GroupsBuffer Mode Passive ModeXx Enter Reading Data from Buffer Mode PortsPort Buffers Modem ModeSending Parameters to a File Saving and Restoring Configuration ParametersRestoring Saved Parameters Upgrading CMS Firmware Command Conventions Command Reference GuideCommand Response Terse Verbose Command SummaryWP n Enter Enter Enter Command Mode Command SetEnter+++Enter Resident Disconnect Sequence ConnectCP Copy RS232 Port Parameters Format /C x x EnterFormat /CP Enter Third Party Disconnect2 Enter or /D/Y 3 Enter Format /D/Y x x EnterErase Buffer Format /E/Y x x EnterHelp Default and TestDisplay Site ID Set RS232 Port Parameters Set Network Port ParametersDisplay Port Status Reset Network Port SD Display Port DiagnosticsSN Display Network Status Save ParametersExit Command Mode UF Upgrade FirmwareFormat /UF Enter Display Port Parameters WhoAppendix A. RS232 Port Interface Appendix B. SpecificationsFormat /X Enter Power Appendix C. Customer ServiceStop Bits 1 or Trademarks Used in this Manual Trademark and Copyright Information
Related manuals
Manual 59 pages 31.71 Kb