Western Telematic CMS-16 manual Configure Option Switches, AC Powered Units, DC Powered Units

Page 14

CAUTION: This device should only be operated with the type of power source indicated on the instrument nameplate. If you are not sure of the type of power service available, please consult your local power company.

4.1.1. AC Powered Units

Plug the supplied power cable into the receptacle on the CMS back panel and then connect the power cable to a grounded AC outlet. The AC powered version of the CMS features a self adjusting power supply that automatically adapts to power supplies between 90 and 250 VAC.

4.1.2. DC Powered Units

The DC terminal block features two bus inputs as shown in Figure 4.1 below. This allows the user to connect only one DC power source, or connect two DC power sources where the second source functions as a backup.

When connecting the CMS to your DC power source, first remove the clear protective cover from the DC terminal block, attach the wires from the -48V DC power source to the screw terminals, connect your ground line to the labeled ground screw, and then replace the protective cover.

Figure 4.1: Terminal Block Assembly (DC Units Only)

4.2. Configure Option Switches

When the CMS is shipped from the factory, the Option Switches are configured for 9600 baud, 8 Bits-No Parity, RTS/CTS handshaking, verbose command response, and command echo ON (all switches Down). These settings are compatible with most applications. If the default settings are not compatible with your application, change the switch settings as follows.

The Option Switches should be configured to match the parameters your control device will use

Image 14

Contents CMS-16 Rack Mount Installation Nameplate Power WarningBattery Replacement Table of Contents Page Appendices List of FiguresIntroduction Typographic Conventions Unit DescriptionFront Panel Power Cable Receptacle Power Switch Back PanelCommunication Parameters Using Other Parameters for this Overview OptionalGetting Started Connecting your PC to the CMS Apply Power to the CMSSystem SetUp Ports Communicating with the CMS UnitCommand Menu Display Configuration ControlPort Name Password StatusHardware Installation Connecting Power to the CMS UnitDC Powered Units Configure Option SwitchesAC Powered Units Default Baud Rate Sw1, Sw2, Sw3 Default Handshake Sw4, Sw5Default Command Echo Sw7 Initialize Unit to Default SettingsDefault Response Message Format Sw6 Connecting Devices to the CMS Application ExampleCMS Application Example Not to Scale Configuration Access to the CMS Command Mode$ telnet 192.1.1.1 Enter Password Functions Supervisor PasswordDefining the Site ID and Supervisor Password Port PasswordsPort Configuration Configuration Conventions3. RS232 Port Configuration Menus Port ModesPort Parameters #02 CTS/RTSATZ Stop Bits Default =Parameters #02 AT&C1$D2S0=1 Network Port Configuration Menu Network Parameters Telnet Port ParametersPage Implementing IP Security IP SecurityPage Copying Parameters to All Ports Copy Port ParametersPort Status Screen /S Status ScreensSave User Selected Parameters Status Mode Buffer Count Port Status Screen Supervisor Mode, Defaults ShownMode BUF CTS Port Diagnostics Screen /SDDiagnostics Name StatusNetwork Status Screen /SN Telnet Port Status Port Parameters Screens /WNetwork Status LAN Status CMSPort Parameters #03 RTS/CTSPort Connection and Disconnection Any-to-Any ModeOperation Disconnecting Ports Enter Defining Hunt Groups Hunt Group ExamplePassive Mode Buffer ModeReading Data from Buffer Mode Ports Xx EnterModem Mode Port BuffersRestoring Saved Parameters Saving and Restoring Configuration ParametersSending Parameters to a File Upgrading CMS Firmware Command Reference Guide Command ConventionsCommand Response Command Summary Terse VerboseWP n Enter Enter+++Enter Resident Disconnect Sequence Command SetEnter Enter Command Mode ConnectFormat /CP Enter Format /C x x EnterCP Copy RS232 Port Parameters Third Party DisconnectErase Buffer Format /D/Y x x Enter2 Enter or /D/Y 3 Enter Format /E/Y x x EnterDisplay Site ID Default and TestHelp Display Port Status Set Network Port ParametersSet RS232 Port Parameters SN Display Network Status SD Display Port DiagnosticsReset Network Port Save ParametersFormat /UF Enter UF Upgrade FirmwareExit Command Mode Display Port Parameters WhoFormat /X Enter Appendix B. SpecificationsAppendix A. RS232 Port Interface Stop Bits 1 or Appendix C. Customer ServicePower Trademark and Copyright Information Trademarks Used in this Manual

Related manuals

Manual 59 pages 31.71 Kb