Perle Systems 5500208-41 manual IPv6 Commands, Set IPv6, Show IPv6

Page 23

IPv6 Commands

IPv6 Commands

Set IPv6

Description	Configures the basic IPv6 settings.
User Level	Admin
Syntax	set ipv6 [dhcpv6-settings ipv6-address onoff]
	[dhcp-settings network-prefix onoff]
	Set ipv6 enable-ipv6-addressing onoff
	[obtain-using auto-ipv6dhcpv6]
Options	dhcpv6-settings
	Determines the types of information that the IOLAN will accept from the DHCPv6
	server, IPv6 address(es) and/or network prefix(es).
	ivp6-address
	When enabled, the IOLAN will accept IPv6 address(es) from the DHCPv6 server. This
	is off by default.
	network-prefix
	When enabled, the IOLAN will accept the network prefix from the DHCPv6 server.
	This is off by default.
	enable-ipv6-addressing
	When enabled, you can configure the IOLAN to obtain the IPv6 address(es) using IPv6
	Autoconfiguration or a DHCPv6 server.
	Default: Enabled
	obtain-using auto-ipv6dhcpv6
	z auto-ipv6—When enabled, the IOLAN will send out a Router Solicitation
	message. If a Router Advertisement message is received, the IOLAN will configure
	the IPv6 address(es) and configuration parameters based on the information
	contained in the advertisement. If no Router Advertisement message is received,
	the IOLAN will attempt to connect to a DHCPv6 server to obtain IPv6 addresses
	and other configuration parameters. This is the default.
	z dhcpv6—When enabled, requests IPv6 address(es) and configuration information
	from the DHCPv6 server.

Show IPv6

Description	Shows the IPv6 settings.
User Level	Admin
Syntax	show ipv6

23

Image 23

Contents Iolan DS1/TS2 EN 55022 1998, Class A, Note Table of Contents User Commands Line Commands Network Commands Time Commands Statistic Commands Glossary Channel Control CommandsIolan DS1/TS2 CLI Reference Guide, Version Intended Audience PrefaceAbout This Book Making a Technical Support Query Contacting Technical SupportFeedback on this Manual Repair ProcedureContacting Technical Support CLI Conventions Command SyntaxIntroduction IntroductionCommand Options Command ShortcutsSet Server Server CommandsServer Commands Set Custom-AppPassword-limit Bypass-passwordDhcp/bootp Oem-loginSingle-telnet Set ServiceTimeout Prompt-with-nameHardware Commands Set Modbus Gateway Modbus CommandsShow TruePort TruePort Baud CommandsUser Level Admin Set TruePort Remap-BaudShow IPv6 IPv6 CommandsSet IPv6 Set Custom-IPv6 Add Custom-IPv6Field Format IPv6 address prefix-bits manual Range Default 64 method manualRange Default Delete Custom-IPv6IPv6 Commands Commands for Users Logged Into the Iolan User CommandsScreen MenuPing ResumeSet User Session Set UserShow Termtype Show Line UsersSyslog Console Show SessionsTcpport TelnetAdd User Configuring UsersSet Default User VersionLevel Hotkey-prefixPhone-number Line-accessService Sess-timerSet User Level Show the settings for the current user Show Default UserConfigureduser Show the settings for the specified userConfiguring Users Set Line Line CommandsPort vs -Port Line Commands Line CommandsBreak-length Break-delayDial-timeout Options breakInternet-address Data-logginInitial Initiate-connectionLock ResetDefault Disabled Session strings Default 10 msTerm1, Term2, Term3 user defined terminals User Stop-bitsTerm-type Set Line Interface Serverport Set Line ServiceConfighost Hostport Initstring Set ModemModemname Show Line Line Service CommandsOptions termtype Set Telnet-ClientEndipaddress Set UDPOutboundport StartipaddressSet Vmodem Set Vmodem-Phone IPaddress Set Modbus-Slave LineSet Modbus-Master Line Set Line Initiate-Connection Set Multihost LineShow Vmodem Show InterfaceShow Telnet-Client Show UDPShow Modems Modem CommandsAdd Modem Delete ModemSet Packet-Forwarding Line Packet Forwarding CommandsEnable-end-eof2 Enable-end-trigger1Enable-end-trigger2 Enable-end-eof1Show Packet-Forwarding Line Packet Forwarding Commands Add Trap Network Commands ChapterSnmp Commands Add CommunityShow Snmp Delete CommunityDelete Trap Set SnmpHosts Commands Tftp CommandsDelete Gateway Gateway CommandsShow Hosts Add GatewayDestinationip Description Configures the gateway User Level Admin SyntaxSet Gateway Show GatewaysShow Syslog Logging CommandsSet Syslog Time/Date Setting Commands Time CommandsTime Commands Show Date Bootup Commands Administration CommandsShow ARP Set BootupShow Bootup Configuration fileFilename Tftp File Transfer CommandsNetload Hostname/ipaddressTable or a DNS server Custom Factory DefaultOptions Factory-default-config NetsaveShow Motd Motd CommandsSet Set MotdMotd Commands Show Modbus Statistics Statistic Commands ChapterConfiguration Statistics Show NetstatRun-Time Statistics Set IO UDP O CommandsGlobal I/O Commands Set IO Modbus Set IO Temperature-ScaleSet Line Set IO FailsafeSet IOChannel Digital Input Set IOChannel ModeSet IOChannel Set IOChannel Digital I/OSet IOChannel Digital Input Serial Pins Will be displayed as active Current status. The default is disabledSet IOChannel Digital Output Description can be up to 20 charactersInactive-to-active-delay Active-signal-widthInactive-signal-width Active-to-inactive-delayRelaynumber Set IOChannel Digital Output Serial PinsSet IOChannel Relay Options descriptionOptions analogchannel Set IOChannel Analog True AnalogClear-level Trigger-typeTrigger-level Clear-modeSet IOChannel Analog Temperature Level Options channel EnabledDefault Disabled keepalive Set IOChannel IOExtensionLocal-connection inputchannel Client-initiated tcp-portClient-initiated multihost Server-initiated tcp-portChannel Set IOChannel MultihostShow IOChannel Status Kill IOChannelShow IOChannel Show IORelay Channel Control CommandsDigital Output Digital InputGlossary