Perle Systems 5500208-41 manual Add Custom-IPv6, Set Custom-IPv6

Page 24

IPv6 Commands

Add Custom-IPv6

Description	Adds a custom IPv6 address to the IOLAN. You can specify either a complete IPv6
User Level	address or an IPv6 network address.
User Level	Admin
Syntax	add custom-ipv6 method auto network-prefix <network_prefix>
	[prefix-bits <0-64>]
	add custom-ipv6 method manual ipv6-address <ipv6_address>
	[prefix-bits <0-128>]
Options	method auto
	When this option is specified, the IOLAN will derive an IPv6 address from the entered
	network prefix and the IOLAN’s MAC address. This is the default option.
	network-prefix
	Specify the IPv6 network prefix. The IOLAN will derive the complete IPv6 address
	from the entered network prefix and the IOLAN’s MAC address.
	prefix-bits (auto)
	Specify the network prefix bits for the IPv6 address.
	Range: 0-64
	Default: 64
	method manual
	Specify this option when you want to enter a specific IPv6 address.
	ipv6-address
	Specify the complete IPv6 address.
	Field Format: IPv6 address
	prefix-bits (manual)
	Specify the network prefix bits for the IPv6 address.
	Range: 0-128
	Default: 64

Set Custom-IPv6

Description	Configures custom IPv6 network and IP addresses.
User Level	Admin
Syntax	set custom-ipv6 <config_ipv6_address> method auto
	network-prefix <network_prefix> [prefix-bits <0-64>]
	set custom-ipv6 <config_ipv6_address> method manual
	ipv6-address <ipv6_address> [prefix-bits <0-128>]
Options	method auto
	When this option is specified, the IOLAN will derive an IPv6 address from the entered
	network prefix and the IOLAN’s MAC address. This is the default option.
	network-prefix
	Specify the IPv6 network prefix. The IOLAN will derive the complete IPv6 address
	from the entered network prefix and the IOLAN’s MAC address.

24	IOLAN DS1/TS2 CLI Reference Guide, Version 4.1

Image 24

Contents Iolan DS1/TS2 EN 55022 1998, Class A, Note Table of Contents User Commands Line Commands Network Commands Time Commands Statistic Commands Channel Control Commands GlossaryIolan DS1/TS2 CLI Reference Guide, Version Preface About This BookIntended Audience Contacting Technical Support Making a Technical Support QueryRepair Procedure Feedback on this ManualContacting Technical Support Command Syntax IntroductionIntroduction CLI ConventionsCommand Shortcuts Command OptionsServer Commands Server CommandsSet Custom-App Set ServerBypass-password Dhcp/bootpOem-login Password-limitSet Service TimeoutPrompt-with-name Single-telnetHardware Commands Modbus Commands Set Modbus GatewayTruePort Baud Commands User Level AdminSet TruePort Remap-Baud Show TruePortIPv6 Commands Set IPv6Show IPv6 Add Custom-IPv6 Set Custom-IPv6Range Default 64 method manual Range DefaultDelete Custom-IPv6 Field Format IPv6 address prefix-bits manualIPv6 Commands User Commands Commands for Users Logged Into the IolanMenu PingResume ScreenSet User Set User SessionShow Line Users Syslog ConsoleShow Sessions Show TermtypeTelnet TcpportConfiguring Users Set Default UserVersion Add UserHotkey-prefix LevelLine-access ServiceSess-timer Phone-numberSet User Level Show Default User ConfigureduserShow the settings for the specified user Show the settings for the current userConfiguring Users Line Commands Port vs -Port Line CommandsLine Commands Set LineBreak-delay Dial-timeoutOptions break Break-lengthData-loggin InitialInitiate-connection Internet-addressReset Default Disabled Session stringsDefault 10 ms LockStop-bits Term-typeTerm1, Term2, Term3 user defined terminals User Set Line Interface Set Line Service ConfighostServerport Hostport Set Modem ModemnameInitstring Line Service Commands Show LineSet Telnet-Client Options termtypeSet UDP OutboundportStartipaddress EndipaddressSet Vmodem Set Vmodem-Phone Set Modbus-Slave Line Set Modbus-Master LineIPaddress Set Multihost Line Set Line Initiate-ConnectionShow Interface Show Telnet-ClientShow UDP Show VmodemModem Commands Add ModemDelete Modem Show ModemsPacket Forwarding Commands Set Packet-Forwarding LineEnable-end-trigger1 Enable-end-trigger2Enable-end-eof1 Enable-end-eof2Show Packet-Forwarding Line Packet Forwarding Commands Network Commands Chapter Snmp CommandsAdd Community Add TrapDelete Community Delete TrapSet Snmp Show SnmpTftp Commands Hosts CommandsGateway Commands Show HostsAdd Gateway Delete GatewayDescription Configures the gateway User Level Admin Syntax Set GatewayShow Gateways DestinationipLogging Commands Set SyslogShow Syslog Time Commands Time CommandsTime/Date Setting Commands Show Date Administration Commands Bootup CommandsSet Bootup Show BootupConfiguration file Show ARPTftp File Transfer Commands NetloadHostname/ipaddress FilenameCustom Factory Default Options Factory-default-configNetsave Table or a DNS serverMotd Commands SetSet Motd Show MotdMotd Commands Statistic Commands Chapter Configuration StatisticsShow Netstat Show Modbus StatisticsRun-Time Statistics O Commands Global I/O CommandsSet IO UDP Set IO Temperature-Scale Set LineSet IO Failsafe Set IO ModbusSet IOChannel Mode Set IOChannelSet IOChannel Digital I/O Set IOChannel Digital InputSet IOChannel Digital Input Serial Pins Current status. The default is disabled Set IOChannel Digital OutputDescription can be up to 20 characters Will be displayed as activeActive-signal-width Inactive-signal-widthActive-to-inactive-delay Inactive-to-active-delaySet IOChannel Digital Output Serial Pins Set IOChannel RelayOptions description RelaynumberSet IOChannel Analog True Analog Options analogchannelTrigger-type Trigger-levelClear-mode Clear-levelSet IOChannel Analog Temperature Level Enabled Default Disabled keepaliveSet IOChannel IOExtension Options channelClient-initiated tcp-port Client-initiated multihostServer-initiated tcp-port Local-connection inputchannelSet IOChannel Multihost Show IOChannel StatusKill IOChannel ChannelShow IO Show IOChannelChannel Control Commands Digital OutputDigital Input RelayGlossary