Perle Systems 5500208-41 manual Global I/O Commands, Set IO UDP

Page 77

9 I/O Commands

Chapter 9

This chapter defines all the CLI commands associated with configuring the IOLAN’s I/O parameters.

Global I/O Commands

Set IO UDP

Description

Sets the UDP settings for I/O unicast messages.

User Level

Admin

Syntax

set io udp [mode onoff]

 

[broadcast-interval <broadcast_interval>]

 

set io udp entry 1234 disabled

 

set io udp entry 1234 <udp_port> <start_ip> [<end_ip>]

Options

mode

 

Enables/disables UDP broadcast of I/O channel status (data).

 

broadcast-interval

 

Enter the interval, in seconds, for UDP broadcasts of I/O channel status (data). Valid

 

values are 1-9999. Default value is 30 seconds.

 

entry

 

You can specify up to four sets of UDP IP address that will receive the I/O unicast.

 

udp_port

 

The UDP port that the IOLAN will use to relay messages to servers/hosts.

 

start_ip

 

The first host IP address in the range of IP addresses (for IPV4 or IPV6) that the

 

IOLAN will listen for messages from and/or send messages to.

 

end_ip

 

The last host IP address in the range of IP addresses (for IPV4, not required for IPV6)

 

that the IOLAN will listen for messages from and/or send messages to.

IOLAN DS1/TS2 CLI Reference Guide, Version 4.1

77

Image 77
Contents Iolan DS1/TS2 EN 55022 1998, Class A, Note Table of Contents User Commands Line Commands Network Commands Time Commands Statistic Commands Glossary Channel Control CommandsIolan DS1/TS2 CLI Reference Guide, Version Intended Audience PrefaceAbout This Book Making a Technical Support Query Contacting Technical SupportFeedback on this Manual Repair ProcedureContacting Technical Support Introduction Command SyntaxIntroduction CLI ConventionsCommand Options Command ShortcutsServer Commands Server CommandsSet Custom-App Set ServerDhcp/bootp Bypass-passwordOem-login Password-limitTimeout Set ServicePrompt-with-name Single-telnetHardware Commands Set Modbus Gateway Modbus CommandsUser Level Admin TruePort Baud CommandsSet TruePort Remap-Baud Show TruePortShow IPv6 IPv6 CommandsSet IPv6 Set Custom-IPv6 Add Custom-IPv6Range Default Range Default 64 method manualDelete Custom-IPv6 Field Format IPv6 address prefix-bits manualIPv6 Commands Commands for Users Logged Into the Iolan User CommandsPing MenuResume ScreenSet User Session Set UserSyslog Console Show Line UsersShow Sessions Show TermtypeTcpport TelnetSet Default User Configuring UsersVersion Add UserLevel Hotkey-prefixService Line-accessSess-timer Phone-numberSet User Level Configureduser Show Default UserShow the settings for the specified user Show the settings for the current userConfiguring Users Port vs -Port Line Commands Line CommandsLine Commands Set LineDial-timeout Break-delayOptions break Break-lengthInitial Data-logginInitiate-connection Internet-addressDefault Disabled Session strings ResetDefault 10 ms LockTerm1, Term2, Term3 user defined terminals User Stop-bitsTerm-type Set Line Interface Serverport Set Line ServiceConfighost Hostport Initstring Set ModemModemname Show Line Line Service CommandsOptions termtype Set Telnet-ClientOutboundport Set UDPStartipaddress EndipaddressSet Vmodem Set Vmodem-Phone IPaddress Set Modbus-Slave LineSet Modbus-Master Line Set Line Initiate-Connection Set Multihost LineShow Telnet-Client Show InterfaceShow UDP Show VmodemAdd Modem Modem CommandsDelete Modem Show ModemsSet Packet-Forwarding Line Packet Forwarding CommandsEnable-end-trigger2 Enable-end-trigger1Enable-end-eof1 Enable-end-eof2Show Packet-Forwarding Line Packet Forwarding Commands Snmp Commands Network Commands ChapterAdd Community Add TrapDelete Trap Delete CommunitySet Snmp Show SnmpHosts Commands Tftp CommandsShow Hosts Gateway CommandsAdd Gateway Delete GatewaySet Gateway Description Configures the gateway User Level Admin SyntaxShow Gateways DestinationipShow Syslog Logging CommandsSet Syslog Time/Date Setting Commands Time CommandsTime Commands Show Date Bootup Commands Administration CommandsShow Bootup Set BootupConfiguration file Show ARPNetload Tftp File Transfer CommandsHostname/ipaddress FilenameOptions Factory-default-config Custom Factory DefaultNetsave Table or a DNS serverSet Motd CommandsSet Motd Show MotdMotd Commands Configuration Statistics Statistic Commands ChapterShow Netstat Show Modbus StatisticsRun-Time Statistics Set IO UDP O CommandsGlobal I/O Commands Set Line Set IO Temperature-ScaleSet IO Failsafe Set IO ModbusSet IOChannel Set IOChannel ModeSet IOChannel Digital I/O Set IOChannel Digital InputSet IOChannel Digital Input Serial Pins Set IOChannel Digital Output Current status. The default is disabledDescription can be up to 20 characters Will be displayed as activeInactive-signal-width Active-signal-widthActive-to-inactive-delay Inactive-to-active-delaySet IOChannel Relay Set IOChannel Digital Output Serial PinsOptions description RelaynumberOptions analogchannel Set IOChannel Analog True AnalogTrigger-level Trigger-typeClear-mode Clear-levelSet IOChannel Analog Temperature Level Default Disabled keepalive EnabledSet IOChannel IOExtension Options channelClient-initiated multihost Client-initiated tcp-portServer-initiated tcp-port Local-connection inputchannelShow IOChannel Status Set IOChannel MultihostKill IOChannel ChannelShow IOChannel Show IODigital Output Channel Control CommandsDigital Input RelayGlossary