Perle Systems 5500208-41 manual Set Line Interface

Page 44

Line Commands

Set Line Interface

Description	Configures line interface (hardware) parameters.
User Level	Admin
Syntax	set line .<number>* interface eia-232 [monitor-dcd onoff]
	[monitor-dsr onoff] [flow nonesofthardboth]
	[speed 507511013415020030060012001800240048009600
	19200384005760011520023040028800custom <baud_rate>]
	set line interface eia-422 [flow nonesofthardboth]
	[speed 50751101341502003006001200180024004800
	960019200384005760011520023040028800custom <baud_rate>]
	set line interface eia-485 [tx-driver-control autorts]
	[flow nonesoft]
	[duplex fullduplex half [echo-suppression onoff]]
	[speed 50751101341502003006001200180024004800
	960019200384005760011520023040028800custom <baud_rate>]
Options	eia-232 eia422 485
	Specifies the type of line that is being used with the IOLAN. Select either EIA-232,
	EIA-422, or EIA-485(TS2 supports only EIA-232).
	monitor-dcd
	Specifies whether the RS-232 signal DCD (Data Carrier Detect) should be monitored.
	This is used with modems or any other device that sends a DCD signal. When it is
	monitored and the IOLAN detects a DCD signal, the line service is started. Default is
	Off. If both Monitor DCD and Monitor DSR are enabled, both signals must be detected
	before the line service is started.
	monitor-dsr
	Specifies whether the RS-232 signal DSR (data set ready) should be monitored. This is
	used with modems or any device that sends a DSR signal. When it is monitored and the
	IOLAN detects a DSR signal, the line service is started. Default is Off. If both Monitor
	DCD and Monitor DSR are enabled, both signals must be detected before the line
	service is started.
	flow
	Defines whether the data flow is handled by the software (Soft), hardware (Hard),
	Both, or None.
	tx-driver-control
	Used with a EIA-485serial interface, if your application supports RTS (Request To
	Send), select this option. Otherwise, select Auto. Default is Auto.
	duplex
	Specify whether the line is Full Duplex (communication both ways at the same time) or
	Half Duplex (communication in one direction at a time).

44	IOLAN DS1/TS2 CLI Reference Guide, Version 4.1

Image 44

Contents Iolan DS1/TS2 EN 55022 1998, Class A, Note Table of Contents User Commands Line Commands Network Commands Time Commands Statistic Commands Channel Control Commands GlossaryIolan DS1/TS2 CLI Reference Guide, Version Intended Audience PrefaceAbout This Book Contacting Technical Support Making a Technical Support QueryRepair Procedure Feedback on this ManualContacting Technical Support Command Syntax IntroductionIntroduction CLI ConventionsCommand Shortcuts Command OptionsServer Commands Server CommandsSet Custom-App Set ServerBypass-password Dhcp/bootpOem-login Password-limitSet Service TimeoutPrompt-with-name Single-telnetHardware Commands Modbus Commands Set Modbus GatewayTruePort Baud Commands User Level AdminSet TruePort Remap-Baud Show TruePortShow IPv6 IPv6 CommandsSet IPv6 Add Custom-IPv6 Set Custom-IPv6Range Default 64 method manual Range DefaultDelete Custom-IPv6 Field Format IPv6 address prefix-bits manualIPv6 Commands User Commands Commands for Users Logged Into the IolanMenu PingResume ScreenSet User Set User SessionShow Line Users Syslog ConsoleShow Sessions Show TermtypeTelnet TcpportConfiguring Users Set Default UserVersion Add UserHotkey-prefix LevelLine-access ServiceSess-timer Phone-numberSet User Level Show Default User ConfigureduserShow the settings for the specified user Show the settings for the current userConfiguring Users Line Commands Port vs -Port Line CommandsLine Commands Set LineBreak-delay Dial-timeoutOptions break Break-lengthData-loggin InitialInitiate-connection Internet-addressReset Default Disabled Session stringsDefault 10 ms LockTerm1, Term2, Term3 user defined terminals User Stop-bitsTerm-type Set Line Interface Serverport Set Line ServiceConfighost Hostport Initstring Set ModemModemname Line Service Commands Show LineSet Telnet-Client Options termtypeSet UDP OutboundportStartipaddress EndipaddressSet Vmodem Set Vmodem-Phone IPaddress Set Modbus-Slave LineSet Modbus-Master Line Set Multihost Line Set Line Initiate-ConnectionShow Interface Show Telnet-ClientShow UDP Show VmodemModem Commands Add ModemDelete Modem Show ModemsPacket Forwarding Commands Set Packet-Forwarding LineEnable-end-trigger1 Enable-end-trigger2Enable-end-eof1 Enable-end-eof2Show Packet-Forwarding Line Packet Forwarding Commands Network Commands Chapter Snmp CommandsAdd Community Add TrapDelete Community Delete TrapSet Snmp Show SnmpTftp Commands Hosts CommandsGateway Commands Show HostsAdd Gateway Delete GatewayDescription Configures the gateway User Level Admin Syntax Set GatewayShow Gateways DestinationipShow Syslog Logging CommandsSet Syslog Time/Date Setting Commands Time CommandsTime Commands Show Date Administration Commands Bootup CommandsSet Bootup Show BootupConfiguration file Show ARPTftp File Transfer Commands NetloadHostname/ipaddress FilenameCustom Factory Default Options Factory-default-configNetsave Table or a DNS serverMotd Commands SetSet Motd Show MotdMotd Commands Statistic Commands Chapter Configuration StatisticsShow Netstat Show Modbus StatisticsRun-Time Statistics Set IO UDP O CommandsGlobal I/O Commands Set IO Temperature-Scale Set LineSet IO Failsafe Set IO ModbusSet IOChannel Mode Set IOChannelSet IOChannel Digital I/O Set IOChannel Digital InputSet IOChannel Digital Input Serial Pins Current status. The default is disabled Set IOChannel Digital OutputDescription can be up to 20 characters Will be displayed as activeActive-signal-width Inactive-signal-widthActive-to-inactive-delay Inactive-to-active-delaySet IOChannel Digital Output Serial Pins Set IOChannel RelayOptions description RelaynumberSet IOChannel Analog True Analog Options analogchannelTrigger-type Trigger-levelClear-mode Clear-levelSet IOChannel Analog Temperature Level Enabled Default Disabled keepaliveSet IOChannel IOExtension Options channelClient-initiated tcp-port Client-initiated multihostServer-initiated tcp-port Local-connection inputchannelSet IOChannel Multihost Show IOChannel StatusKill IOChannel ChannelShow IO Show IOChannelChannel Control Commands Digital OutputDigital Input RelayGlossary